Panasonic KX-UTG200 Setup Manual Download

Page: 263 / 412

Description

Specifies whether or not the CPE can use STUN. This applies only to
the use of STUN in association with the ACS to allow UDP Connection
Requests.

Value Range

•

Y/Yes

(Enable)

•

N/No

(Disable)

Default Value

ANNEX_G_STUN_SERV_ADDR

Value Format

String

Description

Specifies the host name or IP address of the STUN server for the CPE
to send Binding Requests.

Note

•

This setting is available only when
"

ANNEX_G_STUN_ENABLE

" is set to "

•

If the value for this setting is an empty string and
"

ANNEX_G_STUN_ENABLE

" is set to "

", the CPE must use the

address of the ACS extracted from the host portion of the ACS
URL.

Value Range

Max. 256 characters

Default Value

Empty string

ANNEX_G_STUN_SERV_PORT

Value Format

Integer

Description

Specifies the port number of the STUN server for the CPE to send
Binding Requests.

Note

•

This setting is available only when
"

ANNEX_G_STUN_ENABLE

" is set to "

Value Range

1–65535

Default Value

3478

ANNEX_G_STUN_USER_ID

Value Format

String

Description

Specifies the STUN username to be used in Binding Requests (only if
message integrity has been requested by the STUN server).

Note

•

If the value for this setting is an empty string, the CPE must not
send STUN Binding Requests with message integrity.

Document Version 2015-01

Administrator Guide

263

5.4.7 Management Server Settings

Summary of Contents for KX-UTG200





























































































































































































































































































































































































































Search results

Summary of Contents for KX-UTG200

Reviews:

Related manuals for KX-UTG200

Brands by name

Popular brands

Panasonic KX-UTG200, Setup Manual

Search results

Summary of Contents for KX-UTG200

Reviews:

Related manuals for KX-UTG200

Brands by name

Popular brands