Panasonic KX-UTG200 Setup Manual Download

Page: 290 / 412

HOLD_RECALL_TIM

Value Format

Integer

Description

Specifies the duration of the hold recall timer. If set to "0", the function
is disabled.

Value Range

0–240 (0: Disable)

Default Value

Web User Interface Reference

Hold Recall Timer (Page 141)

AUTO_ANS_RING_TIM

Value Format

Integer

Description

Specifies the number of seconds a phone in Auto Answer mode will ring
before a conversation is established automatically when it receives a
call.

Value Range

0–15

Default Value

ONHOOK_TRANSFER_ENABLE

Value Format

Boolean

Description

Specifies whether transfer operations are permitted while on-hook.

Value Range

•

Y/Yes

(Enable On-hook Transfer)

•

N/No

(Disable On-hook Transfer)

Default Value

KEY_PAD_TONE

Value Format

Integer

Description

Selects whether a tone is heard in response to key presses.

Value Range

0–3

–

0: high

–

1: middle

–

2: low

–

3: off

Default Value

Web User Interface Reference

Key Click Tone (Page 162)

290

Administrator Guide

Document Version 2015-01

5.6.1 Call Control Settings

Summary of Contents for KX-UTG200





























































































































































































































































































































































































































Search results

Summary of Contents for KX-UTG200

Reviews:

Related manuals for KX-UTG200

Brands by name

Popular brands

Panasonic KX-UTG200, Setup Manual

Search results

Summary of Contents for KX-UTG200

Reviews:

Related manuals for KX-UTG200

Brands by name

Popular brands