Panasonic KX-UTG200 Setup Manual Download

Page: 110 / 412

4.3.7.1 HTTP Client Settings

HTTP Version

Description

Selects which version of the HTTP protocol to use for HTTP
communication.

Value Range

•

HTTP/1.0

•

HTTP/1.1

Note

•

For this unit, it is strongly recommended that you select

[HTTP/

1.0]

. However, if the HTTP server does not function well with

HTTP/1.0, try changing the setting

[HTTP/1.1]

Default Value

HTTP/1.0

Configuration File Reference

HTTP_VER (Page 279)

HTTP User Agent

Description

Specifies the text string to send as the user agent in the header of HTTP
requests.

Value Range

1-64 characters

Note

•

You cannot leave this field empty.

•

If "{mac}" is included in this field, it will be replaced with the
unit’s MAC address in lower-case.

•

If "{MAC}" is included in this field, it will be replaced with the
unit’s MAC address in upper-case.

•

If "{MODEL}" is included in this field, it will be replaced with the
unit’s model name.

•

If "{fwver}" is included in this field, it will be replaced with the
firmware version of the unit.

Default Value

Panasonic_{MODEL}/{fwver} ({mac})

Configuration File Reference

HTTP_USER_AGENT (Page 279)

4.3.7.2 HTTP Authentication

Authentication ID

Description

Specifies the ID for the User account. If set, this name must be entered
to access the Web user interface at the User access level.

Value Range

Max. 127 characters

Default Value

Not stored.

110

Administrator Guide

Document Version 2015-01

4.3.7 HTTP Client Settings

Summary of Contents for KX-UTG200





























































































































































































































































































































































































































Search results

Summary of Contents for KX-UTG200

Reviews:

Related manuals for KX-UTG200

Brands by name

Popular brands

Panasonic KX-UTG200, Setup Manual

Search results

Summary of Contents for KX-UTG200

Reviews:

Related manuals for KX-UTG200

Brands by name

Popular brands