Panasonic KX-UTG200 Setup Manual Download | Manualshive

Page: 370 / 412

background image

Note

•

Make sure that the import source or unit is in standby mode.

•

The import source or unit must be specified at the time of import/export. The imported data is added
to the existing phonebook data.

–

If the existing phonebook data has an entry with the same record ID as an imported entry, the entry
is overwritten with the imported entry.

–

If the existing phonebook data has an entry with no record ID, it will be left in the phonebook.

–

If the imported phonebook data has an entry with no record ID, the imported entry is added as a
new entry unless an existing entry with the same name and phone number is found.

Phonebook entries that are added via the unit are not assigned record IDs. Therefore, it is
recommended to export phonebook data from the unit, assign record IDs manually and then re-import
them. Doing so can help manage phonebook data.

•

The phonebook for a unit has the following limitations:

–

A maximum of 1,000 phonebook entries can be stored in the unit. If the unit already has phonebook
data, it accepts up to the 1,000th entry, including the existing entries. The rest of the entries will
not be imported, and the message "Phonebook entries reach max count, the exceeded entry may
not import to phone" is displayed on the web user interface.

–

The name can contain up to 24 characters.

–

The phone number can contain up to 32 digits.

–

Phonebook entries exceeding the characters or digits limits cannot be imported properly.

–

"Invalid file format" is displayed on web user interface if the imported file is not CSV file, or if there
is a syntax error.

•

If the export is interrupted by an operation on the unit, only the data that has been successfully exported
before the interruption is exported to a file.

6.2 Dial Plan

The dial plan settings control how numbers dialed by the user are transmitted over the network. Dial plan
settings can be configured on a per-line basis. These settings can be programmed either through the Web
user interface (

®

see

4.6.2.2 Dial Plan

) or by configuration file programming (

®

5.9.2 Per Line - Call

Control Settings

370

Administrator Guide

Document Version 2015-01

6.2 Dial Plan

«
...
368
369
370
371
372
...
»

Summary of Contents for KX-UTG200





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for KX-UTG200

Brand: N-Com Pages: 33

Brand: ideus Pages: 2

Brand: QooPro Pages: 14

Savi Office WO100

Brand: Plantronics Pages: 24

Brand: Logitech Pages: 10

Brand: NATIVE UNION Pages: 33

DELTACO DELO-0651

Brand: Nordic Pages: 16

Brand: Genesys Pages: 10

Brand: Plantronics Pages: 17

Brand: Craftsman Pages: 4

Engage 75 Convertible

Brand: Jabra Pages: 2

Brand: Genesis Pages: 10

LifeTalks IH-H411UP

Brand: iHome Pages: 4

Brand: Axis Pages: 24

Brand: Standard Horizon Pages: 24

Brand: TECOM Pages: 2

Brand: Snom Pages: 3

Brand: Sandberg Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands