Panasonic KX-UTG200 Setup Manual Download | Manualshive

Page: 376 / 412

background image

Icon

Description

Indicates a BLF flexible button is subscribing.

Indicates a BLF flexible button is idle.

Indicates a BLF flexible button is busy.

Indicates a BLF flexible button is alert.

Indicates a call with BLF flexible button is parked.

Using Flexible Buttons with the KX-UTA336 Add-on Key Module

(KX-UTG300 only)

The optional KX-UTA336 (also referred to as "KEM") allows 36 additional flexible buttons (3 pages of 12) to
be used with the KX-UTG300. The available flexible buttons (

®

see Page 375) and their icons (

®

see

Page 375) are the same as for the unit. The flexible buttons for the KX-UTA336 can be programmed either
through the Web user interface (

®

see

4.6.4 Flexible Button Settings (KEM) (KX-UTG300 only)

) or by

configuration file programming (

®

see

5.6.10 KEM1 (KX-UTA336 Add-on Key Module 1) Button

and

5.6.11 KEM2 (KX-UTA336 Add-on Key Module 2) Button Settings)

.

6.3.1 Flexible Button Settings

To set Flexible Buttons
1.

In the Web user interface, click the

[Telephone]

tab, and then click

[Flexible Button Settings]

.

2.

Enter settings as described in the following table.

Button

Parameter

Description

Value

One-Touch

Phone Number

Up to 32 digits

BLF

Extension Number

Up to 32 digits

*1

You can also assign extension numbers automatically to BLF buttons using the information in the server's resource list without having
to input information here.

Note

•

For details about configuring these settings by configuration file programming, see

5.6.9 Flexible

Button Settings

376

Administrator Guide

Document Version 2015-01

6.3.1 Flexible Button Settings

«
...
374
375
376
377
378
...
»

Summary of Contents for KX-UTG200





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for KX-UTG200

GN9330e - USB - Headset

Brand: Jabra Pages: 2

Brand: Jabra Pages: 16

Brand: Jays Pages: 12

Brand: Fava Pages: 12

Brand: Aegisound Pages: 16

Brand: Jabra Pages: 2

Brand: Bang & Olufsen Pages: 24

Brand: Manhattan Pages: 5

Brand: Bone Pages: 4

CIT200 - iPhone USB VoIP Wireless Phone

Brand: Linksys Pages: 100

Brand: Honeywell Pages: 70

HOWARD LEIGHT SYNC ELECTO

Brand: Honeywell Pages: 60

Brand: Honeywell Pages: 28

Brand: Honeywell Pages: 29

Brand: Honeywell Pages: 334

Brand: Honeywell Pages: 2

Brand: SpectraLink Pages: 44

WEP250 - WEP 250 Bluetooth Headset

Brand: Samsung Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands