Panasonic KX-UTG200 Setup Manual Download | Manualshive

Page: 40 / 412

background image

2.1 What is Provisioning?

Provisioning is a mechanism that allows the phone to configure itself by retrieving the required settings from
a central provisioning server. This enables mass deployment to be done easily and quickly.
There are two steps required to perform provisioning of the device.

Step 1: Obtaining Provisioning URL setting

This step involves obtaining the URL of the provisioning server either manually or automatically, and
downloading the initial configuration file.

Step 2: Provisioning device information

This step involves downloading the actual device configuration files needed for the operation of the device.

2.2 Provisioning URL Settings

The provisioning URL can be obtained using the following methods.

–

Automatic discovery via SIP PnP, DHCP option 160/159/66, or via a redirection server

–

Manual configuration via web user interface or phone user interface

Priority of the different methods

The device can use IPv4 addresses, IPv6 addresses, or operate in dual-stack mode. By default, IPv4
addresses are preferred over IPv6 addresses. During provisioning, the device checks the status of its interface
and determines whether it is configured with an IPv4 address, an IPv6 address, or both.
The order of priority is as follows.

Device has IPv4 address only

Device has IPv6 address only

Device has IPv4 and IPv6

addresses

1.

Manual configuration

2.

SIP PnP

3.

DHCP option 160

4.

DHCP option 159

5.

DHCP option 66

6.

Redirection server

1.

Manual configuration

2.

DHCPv6 sub-option 1

1.

Manual configuration

2.

SIP PnP

3.

DHCP option 160

4.

DHCP option 159

5.

DHCP option 66

6.

DHCPv6 sub-option 1

7.

Redirection server

Information included when specifying the provision URL

–

Provisioning protocol
Supported protocols: TFTP, FTP, HTTP and HTTPS

–

Provisioning server address
Supported format: IP, FQDN

–

Full path to the subdirectory of the initial configuration file
The initial configuration file contains the device configuration URL and the certification URL.

Valid URL formats

–

<protocol>://<username>:<password>@<IP address>

or

<domain>:<port>

–

IP address

40

Administrator Guide

Document Version 2015-01

2.2 Provisioning URL Settings

«
...
38
39
40
41
42
...
»

Summary of Contents for KX-UTG200





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for KX-UTG200

Brand: Samsung Pages: 2

Brand: Samsung Pages: 8

Brand: Samsung Pages: 81

Brand: Samsung Pages: 48

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

SBH700 - Headset - Behind-the-neck

Brand: Samsung Pages: 2

Brand: Samsung Pages: 3

Brand: Samsung Pages: 6

WEP475 - Bluetooth Headset

Brand: Samsung Pages: 83

Brand: RTX Pages: 7

Brand: Jabra Pages: 2

Brand: Gembird Pages: 12

ZuM Prestige Combo

Brand: Spracht Pages: 24

ULTRALIGHT OP HEADSET TOPS

Brand: Hello Direct Pages: 8

Brand: Hama Pages: 27

Brand: Jabra Pages: 18

Brand: Jabra Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands