Panasonic KX-UTG200 Setup Manual Download

Page: 65 / 412

Main Menu Item

Sub Menu Item

Access

Level

Speed/Duplex

Embedded Web

Port Mirroring

HTTP Authentication

Provisioning

Multicast Paging

Application Settings

—

Network Test

—

Change Level

—

Reset

Exclude Private Settings

Exclude Network Settings

Restart

—

The access levels are abbreviated as follows:
U: User; A: Administrator
A check mark indicates that the setting is available for that access level.

3.1.2 Direct Commands

The following table shows additional features programmable with direct commands. These commands are
hidden from end users.

Direct

Command

Feature

Ref.

[#][1][3][6]

Resetting the unit

Page 37

[#][5][3][4]

Embedded web

Page 32

[#][5][9][0]

Port Mirroring

Page 66

[#][6][1][1]

Disable the touch screen

Page 66

[#][6][2][2]

Export phone user interface settings

Page 66

Only available for the KX-UTG300.

Only available for the KX-UTG300 when there is a connected USB flash drive.

Note

•

Key combinations for direct commands can be customized. See the following for more information.

–

Resetting the unit: DIR_CMD_FACTORY_RESET (Page 296)

–

Embedded web: DIR_CMD_ENABLE_EMBEDDED_WEB (Page 296)

–

Port Mirroring: DIR_CMD_ENABLE_PORT_MIRROR (Page 296)

–

Disable the touch screen: DIR_CMD_DISABLE_TOUCH_SCREEN (Page 296)

Document Version 2015-01

Administrator Guide

3.1.2 Direct Commands

Summary of Contents for KX-UTG200





























































































































































































































































































































































































































Search results

Summary of Contents for KX-UTG200

Reviews:

Related manuals for KX-UTG200

Brands by name

Popular brands

Panasonic KX-UTG200, Setup Manual

Search results

Summary of Contents for KX-UTG200

Reviews:

Related manuals for KX-UTG200

Brands by name

Popular brands