Panasonic KX-UTG200 Setup Manual Download | Manualshive

Page: 66 / 412

background image

3.1.3 Port Mirroring Settings

Port mirroring is used for network monitoring and debugging purposes.
You can enable port mirroring by performing the procedure below from the unit.

To enable port mirroring
1.

On the Home screen, select

.

2.

Press

[#][5][9][0]

.

3.

Select

Yes

.

3.1.4 Disabling the Touch Screen

Touch for the screen can be disabled. This is convenient when cleaning the screen.
You can disable touch for the screen by performing the procedure below from the unit.

To disable touch for the screen
1.

On the Home screen, select

.

2.

Press

[#][6][1][1]

.

3.

Select

Yes

.

•

Press

[#][6][1][1]

to enable the screen again.

3.1.5 Exporting phone user interface settings

Exporting of phone user interface settings is only available for the KX-UTG300 when it has a USB flash drive
connected to it.
You can export phone user interface settings to a USB flash drive by performing the procedure below from the
unit.

To export phone user interface settings
1.

On the Home screen, select

.

2.

Press

[#][6][2][2]

.

3.

Select

Yes

.

•

If the export is successful, "Export UI Configuration Successful!" is displayed.

•

If the export fails, "Export UI Configuration Failed!" is displayed.

66

Administrator Guide

Document Version 2015-01

3.1.5 Exporting phone user interface settings

«
...
64
65
66
67
68
...
»

Summary of Contents for KX-UTG200





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for KX-UTG200

Brand: Jabra Pages: 32

Brand: Clas Ohlson Pages: 20

Brand: Sigtronics Pages: 2

Brand: Cardo Systems Pages: 2

Brand: Jabra Pages: 13

Brand: Boult Audio Pages: 5

Brand: Profoon Pages: 40

Brand: Acer Pages: 5

Brand: ASKA ELECTRONICS Pages: 2

Brand: Yealink Pages: 12

Brand: Advanced Wireless Communications Pages: 10

Brand: SCUD Pages: 3

Brand: Cyber Blue Pages: 6

Brand: Cyber Blue Pages: 7

Brand: GN Pages: 19

Brand: David Clark Pages: 2

Brand: Axis Pages: 24

Yapster TM-YW100A

Brand: TekNmotion Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands