Note
•
"Subnet mask"
can only be set when
"IPv4"
is set for
"IP Address Format"
.
•
"Prefix length"
can only be set when
"IPv6"
is set for
"IP Address Format"
.
•
If
"IPv4"
is set for
"IP Address Format"
,
and
"Destination"
,
"Subnet mask"
, or
"Gateway"
contains 1 or 2 digit numbers,
enter these numbers as they are. Do not
enter like [.001].
Example: The IP address is [192.168.0.1].
–
Correct entry: [192.168.0.1]
–
Wrong entry: [192.168.000.001]
•
For the input format for
"Destination"
and
"Gateway"
when
"IPv6"
is set for
"IP
Address Format"
"LAN Mode (LAN 2)"
: Press
[ENTER]
and use
[
][
]
to select the LAN mode.
–
"1 Gbps (Auto)"
: Negotiates with the other
party to determine the LAN mode. The
maximum setting is 1 Gbps (full duplex).
–
"1 Gbps (Fix)"
: Fixes the LAN mode to 1 Gbps
(full duplex).
–
"100 Mbps (Auto)"
(default): Negotiates with
the other party to determine the LAN mode. The
maximum setting is 100 Mbps (full duplex).
–
"100 Mbps (Fix)"
: Fixes the LAN mode to 100
Mbps (full duplex).
–
"10 Mbps (Fix)"
: Fixes the LAN mode to 10
Mbps (full duplex).
Note
•
"LAN Mode (LAN 2)"
is not available if
"LAN 2"
is set to
"OFF"
•
This setting is only displayed for the
KX-VC2000.
•
Match settings according to the hub or
router to be connected.
•
When
"10 Mbps (Fix)"
is set, set the
"Max.
Bandwidth"
of
"Call set up"
to 10 Mbps or
11.
Press
[G]
.
•
A dialogue box to confirm the saving of settings
is displayed.
12.
Use
[
][
]
to select
"Yes"
and press
[ENTER]
.
•
The routing list screen is displayed.
Note
•
To continue setting another routing, repeat
steps
•
The input
"Destination"
is converted to a
network address and then used. There is no
need to register multiple destination IP
addresses that have the same network
address.
13.
Press
[BACK]
.
•
The system settings screen is displayed.
Making Connection Settings
Note
•
You can use the administrator menu to hide the
connection settings screen (Page 153).
1.
Select
"Call set up"
and press
[ENTER]
.
•
The connection settings screen is displayed.
2.
Use
[
][
]
to select the following items for input:
•
The following items are displayed over 3 pages.
To view all the items, press
[R]
to move to the
next page, and press
[B]
to move to the
previous page.
Note
•
You must save the settings separately
for each screen on which you changed
the settings.
•
When
"SIP"
is set to
"OFF"
on the call
type settings screen (Page 143),
"Encryption (SIP)"
cannot be set.
•
When
"H.323"
is set to
"OFF"
on the
call type settings screen (Page 143),
"Encryption (H.323)"
cannot be set.
"Answer Mode"
: Use
[
][
]
to select how to
answer video conference calls (
"Manual"
[default],
"Auto"
, or
"Forced Answer"
"More than one incoming call"
: Use
[
][
]
to
select whether to accept calls from Sub Sites to
make video conferences of more than 2 parties.
–
"ON"
(default): Allow calls with more than 2
parties.
–
"OFF"
: Do not allow calls to have more than 2
parties.
Note
•
For sites operating as "Main Sites" in
multiple-party video conference calls using
the built-in MCU, select
"ON"
.
•
When using a KX-VC1000 that has not
been expanded for 4 Point Built-in MCU
support,
"More than one incoming call"
is
not displayed.
Document Version 2018-01
User Manual
121
Contacts and Settings
