background image

5

 Safety Precautions

Make sure to follow these instructions

 CAUTION

When stir frying with Ceramic Hob, 
observe the following points:

•  Do not leave this Ceramic Hob 

unattended.

•  Do not overheat.
•  Use lower power level for preheating. 

(If a small quantity of oil is used and 
heated excessively, the oil temperature 
will rise rapidly and the oil may catch 
fire. If the bottom of the pot is thin, it 
may become red due to the heat).

When using the power level “9” of 
Ceramic Hob:

•  Do not use for stir frying. The bottom of 

the pot may be deformed.

•  Do not use for simmering. The 

ingredients may boil over.

•  When boiling water, turn down the 

power level as soon as the water 
has boiled. Water may boil or splatter 
around.

Please use caution when unpacking, 
installing or moving this product, as 
some exposed edges may be sharp 
to the touch and may cause injury if 
not handled with care. 

To protect the Glass Panel from 
damage, observe the following 
instructions:

•  Do not place portable gas burner, steel 

cylinders or canned goods. They would 
burst if mistakenly heated.

•  Do not let metallic objects such as 

knives, forks, spoons, lids, aluminium 
foil / tray, retort pouch, magnetic ring, 
watch or accessories be placed on / 
near the top or be touched to cookware 
during Ceramic Hob is operating as 
they may get hot and cause burns or 
injuries.

•  Do not apply high pressure on Glass 

Panel or drop things on it.

•  Do not use harsh abrasive cleaners 

or sharp metal scrapers to clean the 
Glass Panel, since they can scratch the 
surface, which may cause shattering of 
the Glass Panel.

Spray cleaner is not to be used for 
cleaning.

A steam cleaner is not to be used. It 
may cause malfunction, if the water 
enters the electric parts.

Do not insert metallic objects such 
as pins or wire into the intake / 
exhaust vent.

Do not disassemble, attempt to 
repair or modify the Ceramic Hob.

For repair, contact the dealer or 
Customer care centre.

Do not replace the parts of the 
Ceramic Hob with spare parts other 
than authorised Panasonic parts.

Do not touch the Glass Panel during 
or after use. Be extra careful when 
the high temperature caution signal 
“H” lights up.

•  Clean the Ceramic Hob after it has 

cooled down.

For proper use of this appliance, 
observe the following instructions:

•  Do not place paper, or any material that 

may burn under the pot. The paper may 
scorch due to the heat of the pot.

•  Do not heat empty pots or overheat. The 

ingredients may burn or the pot may be 
damaged.

•  Danger of fire : Do not store items on 

the cooking surfaces.

•  Do not use the product for purpose 

other than cooking.

•  Do not heat and scorch empty 

enamelled pots. The Glass Panel may 
be damaged by melted bottom.

•  Do not rub the Glass Panel with the 

bottom of the pot or place a hot pot on 
it. The Glass Panel may be damaged or 
discoloured.

Summary of Contents for KY-R645RLJPQ

























Reviews: