29
28
洗滌的中途供水。
對於被洗滌的衣物水位過高。
對於被洗滌的衣物水位過低。
水位下降時，洗衣機自動供水。
衣物在洗滌前浸過水，或洗衣槽內有積水時，水位有時會過高。
洗滌化纖或混紡等布料的輕質衣物時，水位有時會過低。
在使用“纖細衣物”程序和選擇較低水位時，有時不會從絲屑過
濾網中出水，也不會進行高低式瀑布水流洗滌。
Check the following before request service
不能供水。
WASH
洗 衣
Troubleshooting
故障維修
報修前檢查以下項目
現象
原因
Symptoms
Causes
Tub begins filling in the middle of
the wash.
Water is not supplied.
The water level is too high for the
amount of laundry being washed.
The water level is too low for the
amount of laundry being washed.
Water does not flow through the lint
filter.”Double Cross Cascade” does
not operate.
When the water level goes down, the tub fills automatically.
Check if the water faucet is turned on.
Check if the water supply and the water supply hose are frozen.
Is the water supply cut off?
Check if the connection of the water supply hose is clogged with
dirt. Please refer to “water supply valve filter” on page 26.
When the laundry is already soaked with water before the wash
or if there is water in the tub before the wash is the water level will
sometimes be higher.
With light clothes made of synthetic or blended fabric, the water
level will sometimes be lower.
With the “DELICATE” courses and the lower water level, water
sometimes will not flow through the lint filter. “Double Cross
Cascade” does not operate when these settings have been
selected.
設定兒童安全鎖後，在洗衣槽內有水的情況下，如果打開蓋子
5
秒以上，則蜂鳴器嗚響。此時，要檢查是否小孩打開了蓋子或
是掉進了洗衣槽裏。
開始運行後，只有“水位”鈕和“過程”鈕可以操作。
其它操作，必須按“關/開”鈕，重新進行設定。
設定了兒童安全，並非異常，見第
23
頁。
按鈕操作不靈。
蜂鳴器鳴響不止，開始進行排水。
完全不運轉。
檢查是否有電源故障。
檢查電源保險是否斷開或斷路器是否啟動。
檢查電源插頭是否插緊。
檢查是否按了電源鈕。
水龍頭已打開了嗎？
檢查是否按了開始鈕。
是否已設定了洗衣程序？
蓋子是否已確實關閉？
在脫水中途，行程突然改變至清洗。
脫水時，洗衣槽不規則旋轉。
洗衣槽旋轉忽快忽慢，以減少肥皂泡的殘留。
RINSE/SPIN
洗滌/脫水
OTHER
其 他
顯示“
CL
”。
Symptoms
Causes
Midway during spinning, the
operation suddenly changes to
rinsing.
If the laundries in the tub bundle to one side, the washing
machine automatically will unravel them by rinsing. (Put laundries
into the tub as flat as possible.)
During spinning, the laundry and
the spinner rotate with irregular
movements.
To avoid soap suds building up, the washing tub turns slowly
and quickly.
If you start with the Rinse cycle,
the tub does not fill with water.
When there is no water in the tub, the machine starts from the
“Spin” cycle to remove any water or wash water in the clothing.
After the “Spin” cycle finishes, the machine feeds water. (When
there is water in the tub, the operation starts with draining.)
The buttons do not work.
Buzzer does not stop and water is
drained.
Does not run at all.
Appear “CL”.
After the washing machine starts operation, only WATER LEVEL,
PROCESS buttons are available during washing process. To
change the other settings, press POWER OFF/ON button and
start from the beginning.
Has the mode been set to the “Child Lock Mode”? When the tub
contains water in the Child Lock Mode, the machine starts
draining while activating the emergency alarm if the lid is left
opened for 5 seconds or more.
Check if there is power failure.
Check if the power fuse has been down or the breaker is actuating.
Check if the power plug is plugged in thoroughly.
Check if the POWER button has been pressed.
Has the water faucet been turned on?
Check if the START button has been pressed.
Has the machine been programmed?
Is the Lid securely closed?
Child Lock Mode has been set, not abnormality, see Page 23.
現象
原因
絲屑過濾網不透水。不進行高低式
瀑布水流洗滌。
檢查是否打開了水龍頭。
檢查水管和供水膠管是否結冰。
是否停水？
檢查供水膠管的接頭處是否被殘渣堵塞。
請參照第
26
頁“供水閥過濾網”。
從清洗步驟開始洗滌時，洗衣槽
不供水。
若衣物偏向一邊，會進行清洗以自動修正衣物偏向一邊的現象。
(請儘量把衣物弄平)
洗衣槽內沒有水時，洗衣機從脫水步驟開始，脫去衣物中含有的
水分。脫水步驟完成後，洗衣機開始供水。(洗衣槽內有水時，
則從排水步驟開始。)
