background image

NA-F62G5 / F65G5 / F70G5 / F75G5 / F75S6 / F70S6

13

• Water level to be deter-

mined by cloth amount
detection is to be 1 rank
higher than the normal
level.

• Pressing the [PowerSoak] switch

selects whether to use correction func-
tion or not. ( [L0] or [L1])

• Press [Start/Pause] button to set water

level raise.

• Clear belt tension data.

It shows belt tensile
force.

• b0 :Belt tension rank 0 (Shipping) Good

Condition.

• b1 :Belt tension rank 1 A little bit loose.
• b2 :Belt tension rank 2 Very loose.

• The error indication dis-

play for past two times.

• [E] shall be indicated initially, press

[Power Soak] button to change last time
to time before last and return to E as ini-
tial mode.

• If there were some abnormal alarm in

the past , [U] or [H] and some number
shall be indicated mutually.

• [U12] , [H15] and abnomal test check

will not be recorded.

• The display for running

number

• [C] should be indicated initially, press

[Power Soak] button to change indica-
tion of digit of operation times.

• Press once : Digit (Thousand-Hundred)

Press twice : Digit (Ten-One)
ex: Press once : shows [12](One thou-
sand two hundred thirty four)

• Running number count including all

[Wash Rinse Spin] processes.

• When exceeding 9999 times, Digit

(Thousand) is indicated.

• Contiune [A000] to [A999]

Number of times 

the [Process] 

button is pressed

Check

 Procedures

Check contents

Lamp illumination condition

Operation condition

Summary of Contents for NA-F62G6

































Reviews: