Panasonic NI -FS770, Operating Instructions Manual

11

English

English

Notes

：

a. Iron the garment directly by pressing the soleplate against

    it or with steam by keeping the soleplate slightly away from

    it, depending on its material.

b. The iron can be used as dry iron without the steam button  

    pressed.

c. When the steam button is pressed, the water pump will 

    pump water into the tank. There will be slight noise and 

    vibration, which are normal.

d. Some noises which can be heard when shaking the iron 

    is the one made when a pipe hits the tank. This is normal. 

e. There could be white powder/particles coming out of the 

    steam vents while using the steam function. They are 

    minerals found in hard water which can be brushed off. 

    This is normal.

 f. The steam will be invisible occasionally, depending on 

    the ambient temperature and indoor brightness.

g. The water will flow from the ventage when the water inlet  

    is facing down.

h. If the water in tank is used out during ironing, turn off the 

    power, unplug the power plug and add water.

2. When the 

powerful steam

 indicator starts illuminating, 

    press the steam button continuously for using steam

    functions.

 ・ 

When used as a horizontal steam iron (refer to page 14), 

    it's more effective in wrinkle removal after the power 

    indicator  light  stops flashing around 20 seconds.

Refer to "After each use" in " Storing " on P14

 ・  

It is available for about 10 minutes of steam usage.

    (The time may vary depending on usages.).

1. 

①　

Place the iron on the

         base securely. 

②

 Plug the power plug

         into the electrical

         outlet.

Using

③　

Slide the power switch to

     “ I ” position.

     The “HIGH

（台灣：高）

” indicator 

      lights up and starts blinking.

2. Press the Set button to start setting 

    the temperature.

• Each time the SET button is pressed, 

   the indicators are switched once in the

   order of “HIGH” → “MED” →”LOW”

    (

台灣：

“

高

”→“

中

”→“

低

”

).

• When the product gets ready to work, the set indicator will 

  light on in red. (The figure shows the case when “HIGH

  (

台灣：高

）

” is set.)

[The indicator blinks 

in red (once/2s): 

in preparation]

About 19 

seconds later 

[The indicator stays on

  in red: ready to work]

Ironing methods and temperature settings

Ironing recommendations

Fabric

Press the 

soleplate

against 

the 

garment

Keep the 

soleplate 

slightly away 

from the 

garment

Polyester

Man-made fiber

Wool

Velvet

Silk

Acrylic

Types of fiber and corresponding usage method.

Types of fiber and corresponding usage method.

Linen

cotton

(Including blended 

 yarn fabrics)

10

• Set the temperature according to the label on the clothes. 

• When you are ironing delicate fabrics or creating a fluffy effect,

   keep the soleplate slightly away from the garment.

• To achieve a good ironing effect, press the soleplate against 

   the garment. Please check the laundry care label on the 

   garment before setting  “HIGH”  or  “MED” .

• Please iron the garments in the order from those labeled "Iron 

  on low heat" to those labeled "Iron on high heat”. It may  take

  several minutes for the setting to change from HIGH to LOW.

• Keep the soleplate away from the clothes when ironing clothes 

  labeled "Iron with cover".

• You can iron any kind of clothes by keeping the soleplate away

   from the clothes.

• The recommended moving speed of the soleplate is about 

  10 cm every 3 seconds.

• Do not use the product on leather products.

• To iron heat-sensitive materials or dark-colored fabrics, test 

  on a small corner of the fabric before ironing the entire

  garment to avoid damages.

• Do not iron clothes labeled "No steam".

HIGH: Powerful steam is emitted at a speed of about 11 

g

/min.

MED : Normal steam is emitted at a speed of about 9 

g

/min.

LOW : No steam is emitted.

Notes:

a. Ironing a man-made fiber garment for a long time may 

    cause shrinkage of the garment.

b. It may take several minutes for the setting to change from 

    “HIGH” to “MED” or “LOW” . (The product is ready to work 

    when the red indicator stops blinking.)

c. When “MED” is set, the temperature regulator in the 

    product will act, and thus the amount of steam will be

    temporarily reduced.

d. To deodorize a garment, set the temperature to “HIGH”. 

    While keeping the soleplate slightly away from the garment,

    use steam to iron the part to be deodorized for 10 seconds.

N/A

MED

HIGH

HIGH is recommended

(MED is also 

 applicable)

2

1

3

(HongKong) (Taiwan)

(Taiwan)

(HongKong)

SET button

HIGH
MED
LOW

(Taiwan)

(HongKong)

(HongKong) (Taiwan)