background image

35

11.3. Disassembly of CASE SW

A’SSY

11.3.1. CASE SW A’SSY

1. Insert screwdriver (-) in a gap of the triangle mark portion

of Case SW A'ssy then pry off Case SW A'ssy.

NOTES

• Be careful not to make a scratch by screwdriver (-) to the

paintwork of Center Crossrail.

• Please put two tapes on the part where a screwdriver (-)

touch to prevent paintwork in the Center Crossrail being
damaged.

2. Remove two connectors.

• Do not pull wire so strongly to remove the connector. The

connector can be taken out while pressing the hook.

NOTES

• The connector is classified by the colour. Connect those

connectors as before so as not to make mistake.

• Be careful not to bite wires between Case SW A'ssy and

Center Crossrail when you install Case SW A’ssy.

11.4. Disassembly of FC (Freezer

Compartment)

11.4.1. SENSOR FC

1. Take Cover Connector FC out.

a. Remove the screw that is fixation of Cover Connector

FC on the right of upper side of FC.

b. Pull Cover Connector FC toward you, unhook the

Hooks(4 portions).

c. Pull Bag Joint from storage part and cut Cable Tie of

Bag Joint, then take out wires and connectors, and
disconnect all of them.

Summary of Contents for NR-B32FX3





















































Reviews: