Panasonic NV-FJ620, Operating Instructions Manual

22

SP

ON

SP

OFF

CH DATE ON

OFF

SP

2

1 3 : 4 5 1 4 : 1 5

27SA

CATEGORY

CH DATE ON

OFF

SP

– –

1 3 : 4 5 1 4 : 1 5

27SA

CATEGORY

END:G-CODE

---------

G-CODE

SET :OK
END:G-CODE

PROGRAMME

  123456---

G-CODE

On Screen Display

END : MENU

CATEGORY SETTING

≥

MOVIE

≥

MUSIC

≥

DRAMA

≥

EDUCA

≥

DOCUM

≥

SPORT

≥

CHILD

≥

NEWS

≥

OTHER

≥

– – – – –

END : MENU

CATEGORY SETTING

≥

MOVIE

≥

MUSIC

≥

DRAMA

≥

EDUCA

≥

DOCUM

≥

SPORT

≥

CHILD

≥

NEWS

≥

OTHER

≥

– – – – –

CH DATE ON

OFF

SP

2

1 3 : 4 5 1 4 : 1 5

27SA

CHECK

: PROG./CHECK

4

Press the Cursor button

 (

1

) 

S

to select the Category.

Then, select the desired category by pressing the
Cursor buttons

 (

3421

) 

S

.

– Alternatively, you can set the category on the Navigator

list. (See page 23 for details.)

– This function is activated when [JET NAVIGATOR] is set

to [ON]. (See page 13.) When [JET NAVIGATOR] is set
to [OFF], procced to the step 6.

5

Press the MENU button 

U

to

make the previous display appear.

6

Press the TIMER (REC) button 

A

 to switch the VCR

over to the timer recording standby mode.

– When [JET NAVIGATOR] is set to [ON], the

[PROGRAMME IS COMPLETE. REMAINING
PROGRAMME 49.] message appers. (See page 13.)

– When [JET NAVIGATOR] is set to [OFF], the

[PROGRAMME IS COMPLETE.] message appears.
(See page 13.)

– Check that [

Á

] is lit on the VCR display.

If it is flashing, check the timer recording details again.
(See page 21.)

Notes:

– When the G-Code number is used for programming, the

recording time may be slightly longer than the actual
programme time.

– Repeat steps 

2

 and 

3

 if [PROGRAMME IS INCOMPLETE.]

appears.

– When programming two or more programmes, repeat

steps 

1

–

6

.

– The procedures for checking and cancelling a timer

programme are the same as on page 21.

To Suspend the Timer Recording Standby
Mode

See page 20.

G-Code Programming

Programming is now easier than ever; simply enter the
G-Code number found in the programme scheduling pages
of newspapers and magazines.
G-Code numbers are numbers assigned to programmes
listed in the TV programme schedule found in newspapers
and TV guides. When these numbers are entered, the
numbers are converted to actual programming.

G-

CODE

 is a registered trademark of Gemstar

Development Corporation. The G-

CODE

 system is

manufactured under licence from Gemstar Development
Corporation.

Preparations

– Confirm that the VCR is on.
– Confirm that the TV is on and the VCR viewing channel is

selected.

– Insert a video cassette with an intact erasure prevention

tab.

– Set the VCR/TV switch 

E

 to [VCR].

– Check that the clock is set to the correct time. If it has not

been set, refer to page 10.

Example:

Programming a timer recording of a TV programme with the
G-Code number 123456

Operations

1

Press the G-CODE/SV button 

H

to

display the menu for entering the
G-Code number on the TV.

2

Press the Numeric buttons 

2

to

enter the G-Code number.

– It is also possible to check the

number with VCR display without
appearing the On Screen Display.

– If you have entered the wrong number, press the

CANCEL button 

;

 then enter the proper number. An

alternative method is to press the Cursor button (

2

) 

S

and then enter the proper number.

3

Press the OK button 

T

.

– The entered programme appears

on the display.

– The starting time and the ending

time appears alternately each
5 seconds on the VCR display.

– Confirm that the number

corresponds to the right
programme. If the display looks
like this and 

Á

 on the VCR

display

flashes on and off: select

the desired programme position
using the Channel button 

9

, then

press the OK button 

T

.

– To make any corrections, use the DATE button 

:

, the

ON button 

D

, the OFF button 

C

 and the SPEED button

B

 the same way as described on page 19.