Panasonic NV-FJ628F Operating Instructions Manual Download

Page: 12 / 24

Timer Recording

This VCR lets you programme up to 16 TV programmes
(including weekly and daily programmes) for unattended
recording up to one month in advance.

To Programme with the On Screen Display
(OSD)

This method offers easy step-by-step programming with the
remote control while you view the prompts on the TV screen.

Example:

Programming the timer recording of a TV programme
broadcast on programme position 2 (M6) from 20:00 to 21:30
on 27 October.

Press the [PROG./CHECK]

(14)

to display the menu for
programming timer recordings on
the TV screen.
• Alternatively, you can press the [MENU]

(7)

and then

select [Timer recording].

Press the [CH]

(12)

to select the programme position of

the desired TV station.
• As an alternative method, after pressing the [CH]

(12)

you can use the [Cursor]

(38)

3421

Press the [DATE]

(11)

to set the date on which the TV

programme will be broadcast.

Press the [ON]

(10)

to set the starting time.

• When it is kept pressed, the indication changes in

30-minute intervals.

Press the [OFF]

(22)

to set the ending time.

Press the [SP/LP/EP]

(21)

to set the desired tape speed.

• Regarding the [A] indication, refer to page 13.

Press the [Cursor]

(38)

3421

to set [VPS/PDC] to

[ON] or [OFF] [

jjj

• See page 13 for VPS/PDC recording.

Press the [OK]

(24)

to conclude

the setting.

Press the [TIMER]

(20)

to switch the VCR over to the

timer recording standby mode.
• Check that [

] is lit on the VCR display.

If it is flashing, check the timer recording details again.
(See page 13.)

To Programme with the S

HOW

IEW

Function

(For NV-FJ732F and NV-FJ632F)

The S

HOW

IEW

numbers make it extremely easy to set the

VCR for timer recording.
The duration of a timer recording programmed with
S

HOW

IEW

number may be slightly longer than the actual

duration of the TV programme.

HOW

IEW

is a registered trademark of Gemstar

Development Corporation. The S

HOW

IEW

system is

manufactured under licence from Gemstar Development
Corporation.

Example:

Programming a timer recording of a TV programme with the
S

HOW

IEW

number 721114

Press the [SV/V+]

(30)

to display

the menu for entering the
S

HOW

IEW

number on the TV.

Press the [Numeric]

(2)

to enter the S

HOW

IEW

number.

• If you have entered a wrong digit, press the [Cursor]

(38)

and then enter the correct digit.

Press the [OK]

(24)

to display the programmed content.

Press the [SP/LP/EP]

(21)

to set the desired tape speed.

• Regarding the [A] indication, refer to page 13.
• To change timer recording programmings, use the

[Cursor]

(38)

3421

, the [CH]

(12)

, [DATE]

(11)

[ON]

(10)

or [OFF]

(22)

• See page 13 for VPS/PDC recording.

Press the [OK]

(24)

again to conclude the settings.

Press the [TIMER]

(20)

to switch the VCR over to the

timer recording standby mode.
• Check that [

] is lit on the VCR display.

If it is flashing, check the timer recording details again.
(See page 13.)

To Suspend the Timer Recording Standby
Mode

Press the [TIMER]

(20)

so that the [

] indication on the

VCR display disappears.
After you have finished using the VCR, be sure to reactivate
the timer recording standby mode by pressing the [TIMER]

(20)

again, otherwise the programmed timer recording will

not be performed.

Note:

• If the VCR is not put in the timer recording standby mode at the

latest 10 minutes before the programmed timer recording starting
time, the [

] flashes on the VCR display. In this case, press the

[TIMER]

(20)

to put the VCR in the timer recording standby mode.

jjjjj

jjj

jjjjj

jjj

jjjjj

jjj

jjjjj

jj jj

jjj

jjjjj

jj jj

jjj

jjjjj

jj jj

jjj

jjjjj

jj jj

jjj

jjjjj

jj jj

jjj

Timer recording

Pos

Start Stop

VPS

Name DATE ON

OFF

PDC

Panasonic VCR

1/2

27/10

20:00

21:30

jjjjj

jjj

jjjjj

jjj

jjjjj

jjj

jjjjj

jj jj

jjj

jjjjj

jj jj

jjj

jjjjj

jj jj

jjj

jjjjj

jj jj

jjj

Timer recording

Pos

Start Stop

VPS

Name DATE ON

OFF

PDC

Panasonic VCR

1/2

ShowView

7 2 1 1 1 4

Panasonic VCR

Summary of Contents for NV-FJ628F

























Search results

Summary of Contents for NV-FJ628F

Reviews:

Related manuals for NV-FJ628F

Brands by name

Popular brands

Panasonic NV-FJ628F, Operating Instructions Manual

Search results

Summary of Contents for NV-FJ628F

Reviews:

Related manuals for NV-FJ628F

Brands by name

Popular brands