Panasonic NV-FJ732F Operating Instructions Manual Download

Page: 13 / 24

If [

] Appears under [Pos/Name] after

Entering a S

HOW

IEW

Number

(For NV-FJ732F and NV-FJ632F)

Pos/Name stands for Programme Position/TV Station Name.
Normally, the name of the TV station or the number of the
programme position is displayed under [Pos/Name].
However, if the [

] indication appears, follow the operation

steps below.

Press the [CH]

(12)

repeatedly to select the programme

position on which the TV programme to be recorded will be
broadcast.

After you have entered the information of a TV station, it
remains stored in the VCR’s memory, and you do not need
to enter it again in the future.

Setting the Recording Date/Day(s)

Press the [DATE]

(11)

to select the recording date (1 to 31),

daily timer recording date (Su–Sa, Mo–Sa or Mo–Fr) or
weekly timer recording date (Su to Sa).

• Programming a timer recording (setting the date) is

possible up to one month ahead of the TV programme’s
broadcasting date and time. Daily and weekly timer
recordings will continue until you cancel them.

Auto SP/LP Change Function

If the VCR determines that the remaining tape time is
insufficient to record the whole programme, LP mode is
automatically selected to ensure that the programme will be
recorded as long as possible.

Press the [SP/LP/EP]

(21)

to select [A].

• This function cannot change the recording speed to the EP

mode.

• If the remaining tape time is still not sufficient even in the

LP mode, the programme cannot be recorded to its end.

• If the recording speed changes from SP to LP during a

timer recording, some brief picture distortion occurs at that
point.

VPS/PDC Function

(For NV-FJ732F and NV-FJ632F)

If a TV programme, for example a football game runs longer
than scheduled, is shortened or starts earlier or later, this
function synchronises the recording start and stop with the
actual broadcasting start and stop of the TV programme.

Press the [Cursor]

(38)

3421

to make the [ON] indication

appear.

• [ON] must be displayed under [VPS/PDC] on the TV

screen.

• The TV station must broadcast VPS/PDC signals.
• The programme starting time must be set correctly to the

starting time listed in the newspaper/magazine.

To Check, Change or Cancel Timer
Recording Programmings

Press the [PROG./CHECK]

(14)

to display the timer

recording programmings on the TV screen.
• When the VCR is in the timer recording standby mode

for a VPS/PDC recording, the On Screen Display may
be distorted.

Press the [Cursor]

(38)

to select the programming

that you want to change or cancel.

Press the [OK]

(24)

To change or cancel timer recording programmings, use
the [Cursor]

(38)

3421

, the [CH]

(12)

, [DATE]

(11)

[ON]

(10)

, [OFF]

(22)

or [CANCEL]

(13)

Press the [OK]

(24)

to conclude the setting.

Press the [EXIT]

(27)

to exit the On Screen Display.

Note:

In some cases, for example as listed below, the programming of a
timer recording remains stored in the memory until 4 a.m. the next
day. However, this is not a malfunction.
• When a timer recording was not performed up to the TV

programme’s ending time because the remaining tape time was
not sufficient.

• When you have stopped the timer recording while it was being

performed.

To Check the Total Timer Recording
Programming Time

The total time indication for timer
recording programming lets you
check how many programmes can
be recorded by comparing with the
remaining tape time in the VCR display.
• The total time is calculated in the SP mode.
• The total time cannot be calculated when setting Daily/

Weekly timer recording.

jjjjj

jj jj

jjj

jjjjj

jj jj

jjj

jjjjj

jjj

jjjjj

jjj

jjjjj