background image

4

LSQT0871

Setting the Remote Control to Operate 
Your TV

You can operate the TVs of the manufacturers listed below 
with the remote control after setting it.

This setting procedure allows you to operate the TVs of some 
manufacturers using the supplied remote control.

Preparation

• Turn on the TV.

Operations
1 Find the manufacturer number of your TV while 

referring to the following table.

2 While holding down [TV-ON/OFF]  

(17)

 on the remote 

control, use [Numeric] 

(3)

 to enter the manufacturer 

number. This completes the settings for the TV 
manufacturer.

• Be sure to enter the number in two digits.

Example: 1 

 ) 

01

3 To confirm the correct settings were made, check 

whether the TV can be operated properly.

• When a manufacturer has multiple numbers in the 

following table, try entering other numbers if the TV 
operations cannot be performed properly, and then select 
the optimal number.

Notes:

• If you are using a Panasonic TV, this setting has already 

been made, and so you do not need to perform the above 
setting procedure. However, this remote control may not 
work with some Panasonic TVs.

• Some TV models cannot be operated using this remote 

control (including all TVs non-remote compatible).

List of TVs Compatible with the VCR Remote Control

Connections

This section shows you how to connect the VCR to an aerial, 
TV, etc.

When the VCR is turned on after unpacking and 
connecting the aerial cable and the mains lead, Plug in 
Auto Tuning starts automatically. 

Basic Connections

The following connections are required to record and play 
back the video cassette through the TV.

Connection to a TV using the Audio/Video Input Socket:

Set the RF output channel of the VCR to [

ss

] (RF OFF) 

when the VCR is connected to the TV via the Audio/Video 
cable. (See page 5.)

Connection to a Stereo Amplifier:

[Brand]

[Code]

Panasonic/National

01-04

SONY

05

TOSHIBA

06

JVC

07

HITACHI

08

MITSUBISHI

09, 10

SHARP

11

PHILIPS, SAMSUNG

12

NEC

13

SANYO

14

GOLDSTAR/LG

15, 16

SAMSUNG

17, 18

SANYO

19

AUDIO

R

VIDEO

IN

OUT

L

OUT

AC IN

 〜

IN(AV1)

RF

(6)

¢

(5)

(4)

(1)

(3)

(2)

 (1) Aerial (Not supplied)
 (2) TV Set (Not supplied)
 (3) Aerial Connector
 (4) RF IN socket 

(44)

 (5) RF OUT socket 

(47)

 (6) AC Input socket 

(41)

  ¢

To mains supply

3  pin mains plug is for Saudi 
Arabia.

AUDIO

R

VIDEO

IN

OUT

L

OUT

AC IN

 〜

IN(AV1)

RF

(10)

(9)

(8)

(7)

(1)

¢

(3)

(4)

(6)

(5)

(2)

(1) Aerial (Not supplied)
(2) TV Set (Not supplied)
(3) Aerial Connector
(4) VIDEO IN
(5) AUDIO IN
(6) AV Cable (Supplied)
(7) RF IN socket 

(44)

(8) RF OUT socket 

(47)

 (9) VIDEO OUT 

(43)

/

AUDIO OUT 

(46)

 (10)AC Input socket 

(41)

  ¢

To mains supply

3  pin mains plug is for Saudi 
Arabia.

AUDIO

R

VIDEO

L

OUT

AC IN

 〜

IN(AV1)

(4)

(3)

(2)

¢

(1)

(5)

(1) Stereo amplifier (Not supplied)
(2) For RECORDING
(3) For PLAYBACK
(4) AUDIO OUT 

(46)

(5) AUDIO IN 

(45)

  ¢

Audio Cables (Not supplied)

LSQT0871_Eng.book  4 ページ  2005年2月16日 水曜日 午後3時39分

Summary of Contents for NV-HV62GCS



















Reviews: