18
Checking a Timer Programme
– The VCR must be turned on, or in timer recording standby
mode.
– Confirm that the TV is on and the VCR viewing channel is
selected.
1
Press the PROG./CHECK button
8
twice.
– Every time you press the PROG./
CHECK button
8
, the programme
shifts below.
2
Press the Cursor button (
1
)
M
to
display the Category. (When [JET
NAVIGATOR] is set to [ON].) Press
the Cursor button (
1
)
M
again to
make the previous display appear
3
Press the MENU button
K
to exit
the On Screen Display.
Cancelling a Timer Programme
– The VCR must be turned on, or in timer recording standby
mode.
– Confirm that the TV is on and the VCR viewing channel is
selected.
1
Press the PROG./CHECK button
8
twice.
2
Press the PROG./CHECK button
8
repeatedly until the desired timer
programme is highlighted.
3
Press the RESET/CANCEL button
H
.
4
Press the MENU button
K
to exit
the On Screen Display.
Note:
– If timer recording is not completed (due to insufficient tape
or cancellation by the user), the programmed timer
recording data will be cancelled from the memory by
4 A.M two days later.
However, if the timer recording function is activated at that
time, the programmed timer recording data will not be
cancelled.
DATE
CH ON
OFF
2 7 W E
2 2 0 :0 2 2 1 :3 0 SP
S U - S A 2 5 1 0 :3 0 1 1 :0 0 A
S U
1 4 1 5 :0 0 1 6 :0 0 SP
1 9 T U
5 2 2 :1 5 2 3 :3 0 EP
2 8 T H
A V 2 0 :0 2 2 1 :3 0 SP
3 0 S A
4 1 9 :1 0 1 9 :5 5 EP
– – – –
– –
– –:– – – –:– –
– – – –
– –
– –:– – – –:– –
END:MENU
1
2
3
4
5
6
7
8
DATE
CH ON
OFF
2 7 W E
2 2 0 :0 2 2 1 :3 0 SP
S U - S A 2 5 1 0 :3 0 1 1 :0 0 A
S U
1 4 1 5 :0 0 1 6 :0 0 SP
1 9 T U
5 2 2 :1 5 2 3 :3 0 EP
2 8 T H
A V 2 0 :0 2 2 1 :3 0 SP
3 0 S A
4 1 9 :1 0 1 9 :5 5 EP
– – – –
– –
– –:– – – –:– –
– – – –
– –
– –:– – – –:– –
END:MENU
1
2
3
4
5
6
7
8
DATE
CH ON
OFF
2 7 W E
2 2 0 :0 2 2 1 :3 0 SP
S U - S A 2 5 1 0 :3 0 1 1 :0 0 A
S U
1 4 1 5 :0 0 1 6 :0 0 SP
– – – –
– –
– –:– – – –:– – EP
2 8 T H
A V 2 0 :0 2 2 1 :3 0 SP
3 0 S A
4 1 9 :1 0 1 9 :5 5 EP
– – – –
– –
– –:– – – –:– –
– – – –
– –
– –:– – – –:– –
END:MENU
1
2
3
4
5
6
7
8
DATE
CH ON
OFF
2 7 W E
2 2 0 :0 2 2 1 :3 0
S U - S A 2 5 1 0 :3 0 1 1 :0 0
S U
1 4 1 5 :0 0 1 6 :0 0
1 9 T U
5 2 2 :1 5 2 3 :3 0
2 8 T H
A V 2 0 :0 2 2 1 :3 0
3 0 S A
4 1 9 :1 0 1 9 :5 5
– – – –
– –
– –:– – – –:– –
– – – –
– –
– –:– – – –:– –
END:MENU
1
2
3
4
5
6
7
8
DATE
CH ON
OFF
2 7 W E
2 2 0 :0 2 2 1 :3 0 SP
S U - S A 2 5 1 0 :3 0 1 1 :0 0 A
S U
1 4 1 5 :0 0 1 6 :0 0 SP
1 9 T U
5 2 2 :1 5 2 3 :3 0 EP
2 8 T H
A V 2 0 :0 2 2 1 :3 0 SP
3 0 S A
4 1 9 :1 0 1 9 :5 5 EP
– – – –
– –
– –:– – – –:– –
– – – –
– –
– –:– – – –:– –
END:MENU
1
2
3
4
5
6
7
8
Timer Recording from an External Signal
Source
If timer recording is performed by a unit connected to the
Audio/Video input sockets, select the AV indicator in step
3
of
4-Key Programming
for the programme position.
CATEGORY
ON
OFF
SP
– – : – – – – : – –
:
1
CH
DATE
27SA
A V
CH
DATE
ON
OFF
A
2 2 0 : 0 2 2 1 : 3 0
27SA
CATEGORY :
1
SP
A
LP
EP
SP
A
EP
On Screen Display
– If the [DIRECT REC] is set to [ON], AV is skipped.
Setting other Programmes in Succession
Repeat steps
1
–
9
of
4-Key Programming
.
Programming a Timer Recording of a TV
Programme Until its End
(Tape Speed Auto Change Function )
If the VCR determines that the remaining tape time is
insufficient to record the programme to its end during a timer
recording performed in the SP mode, this function
automatically changes the tape speed to ensure that the
whole programme will be recorded.
The tape speed will change as follows.
PAL system:
SP
)
LP
NTSC system:
SP
)
EP
– This function cannot change the recording speed to the
EP mode for PAL system.
Depending on the remaining tape length, recording may be
performed in the LP (EP) mode from the start. However, if the
remaining tape time is still not sufficient in this case, the
programme cannot be recorded to the end.
– The tape length must be set correctly. (See page 11.)
– Some tapes may not work correctly.
– If the recording speed changes from SP to LP during a
timer recording, some brief picture distortion occurs at that
point.
To Activate the Tape Speed Auto Change Function:
Press the SPEED button
9
to select [A].
– Every time you press the
SPEED button
9
,
the indication
changes in the following order:
PAL system:
NTSC system:
