Getting Star
ted
11
RQTV0057
Tuning the TV to Your Unit
The unit supplies a signal to the TV via the RF coaxial cable on
channel AU28
s
69 or NZ21
s
69. It is possible to view the unit’s
picture on your TV in the same way that you watch TV broadcasts.
The unit is fitted with its own tuner (just like a normal TV) and can be
preset to receive up to 99 TV broadcast stations.
≥
Press
[VHS]
.
¬
If you have connected the unit to the TV through the audio/
video output sockets
You do not need to follow the procedure below. To view the pictures
from the unit, set to the AV mode on the TV with
[AV]
.
The local TV broadcast channels 2, 7, 9, 10 and 28 are factory-
preset in the unit.
That is, if you can receive TV broadcasts on VHF channels 2, 7, 9,
10 and UHF channel 28, these are already tuned on the programme
positions with the matching numbers.
........................................................................................................................................................................................................................
[1]
Press [
Í
VHS] to turn on
this unit.
.........................................................................................................................
[2]
Hold down [MENU] for 5
seconds or more.
.........................................................................................................................
[3]
Set the TV to an unused
position for the unit
viewing channel.
≥
Tune the TV until the display shown on the right appears. Refer
also to the TV’s instructions regarding tuning.
........................................................................................................................................................................................................................
[4]
Press [MENU].
When the unit is turned on after
connecting the aerial cable and the
mains lead for the first time, tuning
starts automatically.
≥
If the unit is turned on with the aerial
not connected, all channels are
skipped.
..............................................................................................................................
[1]
Press [
Í
VHS] to turn on
this unit.
..............................................................................................................................
[2]
Set the TV to an unused
position for the unit
viewing channel.
..............................................................................................................................
[3]
Press [MENU].
ª
To cancel Auto Tuning halfway through
Auto Tuning will stop halfway by turning the unit off, pressing
[MENU]
,
playback or power failure.
¬
If Auto Tuning stops halfway by turning the unit off, playback
or power failure
≥
Disconnect the mains lead and then reconnect it.
≥
Turn on the unit. Plug in Auto Tuning restarts.
¬
To set the channels manually
(
l
21)
ª
To restart Plug in Auto Tuning
≥
Turn the unit on.
≥
Make sure there is no video cassette in the
unit.
1) Keep
both
[
J
CH]
and
[
I
CH]
on the
unit pressed simultaneously for 3
seconds or more until the channel on
the unit’s display changes to 1.
2) Disconnect the mains lead and then reconnect it.
3) Turn on the unit. Plug in Auto Tuning restarts.
You can change the RF output channel,
for example, when interference occurs on
the picture after tuning.
.........................................................................................................................
[1] Press [MENU] for 5
seconds or more.
.........................................................................................................................
[2] Press [
J
CH] or [
I
CH
]
to
select the channel
(AU28
s
69, NZ21
s
69).
≥
Each time you press
[
J
CH]
or
[
I
CH]
, (
l
below).
≥
Set to “
ss
” (RF OFF) when you
use the audio/video cable for the
connection.
≥
You can also use the numeric buttons.
Example: “28”; [2]
l
[8]
.............................................................................................
[3] Retune your TV to
the new RF
channel for the
unit.
.............................................................................................
[4] Press [MENU] to
exit the setting
mode.
Note:
≥
Even if the RF output channel has been changed, it is not
necessary to perform Auto Tuning.
Pre-programmed TV Channels (for NV-VP33GL/Australia)
Plug in Auto Tuning (for NV-VP33GN/New Zealand)
END : MENU
Panasonic
END : MENU
CH 22
SEARCH
21
END : MENU
AUTO TUN I NG I S
COMPLETED .
Disappears
1
To Change the RF Output Channel
END : MENU
Panasonic
NV-VP33GL
NV-VP33GN
2
8
…
69
(RF OFF)
NV-VP33GL
21
69
(RF OFF)
NV-VP33GN
VP33GL.book 11 ページ ２００５年４月２８日 木曜日 午後５時３４分
