background image

2-Way FRS Radio

Model No.

KX-TR320CF

KX-TR325CS

Operating Instructions

PLEASE READ BEFORE USE
AND SAVE.

PQQX12651XA-BM

FM0200NN2060

D

1 Getting Started
2 Before You Talk
3 To Communicate
4 Channel Scan
5 Special Features
6 Using the Options
7 Things You Should Know

Contents by Section

Getting Started

1

1-A Location of Controls

The illustrations used in this manual are of the KX-TR325.

Accessory

Belt Clip . . . . . . . . . . . . . one 

1-B Display

MIC

SP

PRIVATE

TALK

VIBE RINGER

MENU

MONIT

OR

CALL

SCAN

SCRAMBLE

LO

C

K

POW

ER

T
A
L
K

MIC (Microphone)/SP (Speaker) Jack 
(6-A)

(LOCK)

 Button (5-A)

(TALK)

 Button 

(1-G, 3-B)

Antenna (1-E)

Ear Speaker (3-C)

(MENU)

 Button (1-G)

(‹)

(›)

 Buttons 

(1-G, 2-A, 3-B)

Flip (3-C)

Main Speaker (3-B)

(CALL)

 Button 

(3-D)

(SCAN)

 Button 

(4-A)

(POWER)

 Button 

(1-F)

Display (1-B)

DC IN 4.5 V Jack 
(6-B)

TALK/BUSY 
Indicator (3-A, 3-B)

Microphone (3-B)

(MONITOR)

 Button 

(3-A)

The flip is open (3-C).

The scrambling function is ON 
(KX-TR325 only) (5-C).

The unit is in the VOX 
mode (6-A).

The key lock function is ON 
(5-A).

The unit is in the vibratory call 
mode (KX-TR325 only) (3-E).

The display shows the 
battery strength (1-C). 

The volume is set to level 2 
(3-B, 3-C, 6-A).

The unit is using the group 
code number 38 
(2-B).  

The unit is using the operating 
channel number 14 (2-A).  

The unit is sending call tones 
(3-D).

The unit is using the channel
scan function (4-A).

KX-TR325CS

Printed in Malaysia

TM

Panasonic Canada Inc.
5770 Ambler Drive,
Mississauga, Ontario L4W 2T3
www.panasonic.ca

NOTICE:
This unit is designed for use only in Canada. Sale or
use of this product in other countries may violate local
laws.

PQQX12651XA-BM  00.7.27 9:53 AM  ページ 1

Summary of Contents for PalmLink KX-TR320CF









Reviews: