197
048
049
Not Used
050
RING DETECT MODE
1 = Normal
2 = Rough
Selects the quality of ringer detection. Use if the
line signal is out of regulation, set to "Rough" so
that the unit may detect the ringing signals.
051
Not Used
052
PULSE RATE
1 = 10 pps
2 = 20 pps
Selects the dial pulse rate 10/20 pps.
053
054
Not Used
055
BUSY TONE CHECK
1 = Off
2 = On
Selects whether to detect the Busy Tone.
056
DIAL TONE CHECK
(Except for USA and Canada
version)
1 = Off
2 = On
Selects whether to detect dial tone before dialing
the telephone number.
057
DC LOOP CHECK
(Except for USA and Canada
version)
1 = Off (will not check)
2 = On (checks)
Selects whether the unit checks the DC Loop
during communication.
058
COMM.JRNL +IMAGE
1 = Off (without image)
2 = On (with image)
Selects whether the machine prints the COMM.
Journal with image.
059
Not Used
060
VERSION
Indicatesthe FAX software version.
061
TX/RX//PRT/CPY COUNTER
TX/RX/PRT/CPY
Displays the transmitted, received, total printed and
copied document count.
062
PRINT COUNTER
1 = Off
2 = On
Selects whether to print in the Fax Parameter List,
the counter information that is displayed in the
Function Parameter No. 61.
063
~
067
Not Used
068
NYSE FAX FORWARD
1=Off
2=On
Selects whether the machine will forward the
incoming and outgoing faxes to a specified ABBR
or One-Touch station.
069
NYSE LOCAL PRINT
1=INC
2=ON
(Allways)
Selects the printing condition for the incoming faxes
after FAX Forwarding.
INC. : Prints only if FAX Forwarding fails.
ON : Always prints.
070
LINE ERROR
1 = 128 lines
2 = 256 lines
3 = 512 lines
4 = 1024 lines
5 = 2048 lines
6 = Off (will not disconnect line)
1. Selects the line disconnect condition during
reception. If the number of line errors exceed this
setting, the unit will disconnect the line.
2. Selects the transmit condition of RTP/PIP or
RTN/PIN. (Available if No.73 ERROR DETECT is
set to "LINES") (See Note 1)
071
TOTAL ERROR
1 = 5%
2 = 10%
3 = 15%
4 = 20%
Selects the transmit condition of RTP/PIP or RTN/
PIN.
(Available if No.73 ERROR DETECT is set to
"RATE") (See Note 2)
072
CONTINUOUS ERROR
1 = Off (unlimited)
2 = 3 lines/STD
3 = 6 lines/STD
4 = 12 lines/STD
Selects the continuous total error criteria of Off/3/6
or 12 lines in Standard mode. If continuous total
error exceeds this setting, the unit will transmit
RTN/PIN. (Available if No.73 ERROR DETECT is
set to “RATE”.)
073
ERROR DETECT
1 = Lines
2 = Rate
Selects the error detect condition Lines/Rate.
074
RTN RECEIVE
1 = Disconnect
2 = Continue
Selects whether to disconnect the phone line or
continue when "RTN" is received.
075
MH/MR/MMR/JBIG
1 = MH (MH only)
2 = MR (MH or MR)
3 = MMR (MH or MR or MMR)
4 = JBIG
Selects the coding scheme.
076
Not Used
077
RX JAM LENGTH
1 = Off (unlimited)
2 = 2 m
3 = 8 m
Selects the maximum length of a received
document that can be printed.
078
079
Not Used
080
DOC TOP FEED
-5.0 mm
~
+5.0 mm
Adjusts the distance between the scanning sensor
ON position and the scanning start position.
Function Parameter Table
No.
Parameter (see Note 3)
Selections
Function
Summary of Contents for Panafax DX-2000
