Recharge Power : .......... USB 5V (minimum 500mA)
AC-Charger Output = DC-Input of unit : ...... DC 9V , 1.5A
E-6
OPERATION
E-5
USB THUMB DRIVE & SD CARD FLASH MEMORY (MP3 PLAYBACK)
The following chart shows how to use USB/SD mode:
KEY
NEXT
FUNC.
BACK
For USB thumb drive & SD Card
Skip to next song (Not usable in REPEAT 1 mode)
DISPLAY
/ FOLDER -
PLAY/ PAUSE
MODE
STOP
Press repeatedly until "USB" or "CARD" is displayed
Start or pause Playback
NORMAL PLAY REPEAT 1 REPEAT ALLREPEAT FOLDERRANDOM PLAY
(NOTE: RANDOM PLAY is limited to songs within a selected folder only.)
»
»
»
»
Stop playback
#
k
c
a
r
T
»
»
#
r
e
d
l
o
F
e
m
it
k
c
a
b
y
a
l
P
Choose folder location on your USB/ SD Card (Not usable in RANDOM play mode)
Skip to pervious song (Not usable in REPEAT 1 mode)
IMPORTANT: REMOVAL OF USB DRIVES & SD CARDS
Never remove SD cards or USB drives from the unit during playback.
Always STOP playback, then press “FUNCTION” key to switch to another mode (RADIO/BT)
before removing your USB/SD memory to prevent damage to your song files and memory
devices itself.
Using Audio Line-in Connection (Aux-input)
This unit comes with 2 Aux-input sockets (AUX IN 1/AUX IN 2), allowing you to connect two
external devices at the same time.
You can switch between the 2 Aux-Input sources to “mix” your music.
- Connect your external device to this unit using a standard stereo headphone (3.5mm to 3.5mm)
cable.
- Press “FUNCTION” key repeatedly until display shows “AUX-1”/ “AUX-2”, depending on which
socket you have plugged into.
- Switch on your external device & activate playback on it.
- Playback of external device will start momentarily. Adjust the volume control of the main unit
and your external device to the desired level.
- Playback control can be done only through your external device.
- Remember to switch off the unit when you finish using the external device.
NOTE:
It takes time to "Open & Verify" a large USB-Drive/ SD-Card, and count all the song files.
If there are many files, it can take up to 60 seconds for this process.
Bluetooth® wireless playback (A2DP Wireless Audio Streaming)
This unit can wirelessly playback audio from any device with Bluetooth A2DP function within approx.
30 feet (10m).
Simply pair your device to this unit to enjoy Wireless Audio Streaming.
How to pair your device to this unit?
- Switch on the unit, and press “FUNC” key repeatedly until display shows BT
- The "BT" symbol in the LCD display indicates the pairing status:
Searching
Pairing
Flashing slowly
Connected
Flashing rapidly
BT symbol stays on
- To force the unit to go into "SEARCHING" mode, press and hold the "PAIR" key for 2 seconds
until the "BT" symbol begins flashing slowly.
- Switch on Bluetooth® function of the device you would like to pair with (Your Smartphone /Tablet
/Laptop).
- Go to your device's Bluetooth® Setting. DEVICE NAME: (BT GHETTO BOX)
- Add or search for devices. Make connection on your device (eg. Press "CONNECT").
- If asked for a pass code, enter “0000”.
*This is a one-time event per device. To pair your unit with another device,
please repeat the above steps. The unit remembers up to 5 devices.
There is no need to repeat this pairing procedure for up to 5 devices,
even if unit is powered off.
The unit will also automatically pair with the LAST paired device if it is found
when the unit is powered on and switched to Bluetooth® mode.
Note that only one device can be paired at any given time, but the unit will remember
up to 5 devices in memory.
Disabling Bluetooth® Connection:
T
seconds until pairing status changes from “CONNECTED” to “SEARCHING”.
(The BT symbol starts flashing slowly)
o unpair a Bluetooth® device that has already been paired, press & hold “PAIR” key for a few
Sound Control:
- Adjusting loudness can be done by rotating the Volume Knob on this unit or the device you
have already paired with.
Note: if there is no playback, ensure the volume on both devices is not set to 0.
Sound Effect (Music Equalization)
To enhance the quality of music, this powerful sound system comes with two additional
equalization functions. At anytime during playback, you can rotate the bass and treble knobs:
for stronger Low frequencies (BASS) or High frequencies (TREBLE).
OPERATION / SPECIFICATIONS
Microphone input
This unit comes with a microphone input function. To utilize this function, simply connect your
microphone to the 6.3mm (1/4”) input socket at the front of this unit. You can adjust the Mic volume
by rotating the microphone volume knob. This function works perfectly during playback of all
input sources including Bluetooth®, FM radio & Aux-Input, so you can sing along with any source
or device.
Specifications
-
Power Supply : ............... Rechargeable Lithium 3.7V/ 2Ah X 2 PCS (Built-in)
AC-Charger Input : ......... AC 100-240V ~ 50/60 Hz
Speaker : ...................... 4"x2
Frequency : .................. FM 87.5- 108 MHz
MP3 : ............................ 16-320 kbps (max. 999 Files/ 99 Folders)
When electrostatic discharge (ESD) occurs at the front surface (whether metal or plastic)
or near any part or any button of this unit, there may be a possibility that the product may
stop operation and/ or shut down immediately.
This is a normal condition and intended to protect the unit and internal components against
damage. In such a case, please reset the unit using the system reset hole (at the rear
of unit), simply insert a paper clip into the reset hole for 2 seconds to revert the unit to normal
operation.
System Reset
Summary of Contents for PBT600
Page 4: ...E 8 ...
