Panasonic PN28160A Operation Manual Download

Page: 271 / 277

271

Appendix E. MIB List

The MIB list of this Switching Hub is as follows.

<port_num> is a port number.
<ip_address> is an IP address.

1.1. system group

MIB object

Access

Identifier

Remarks

sysDescr RO

sysDescr.0

sysObjectID RO

sysObjectID.0

sysUpTime RO

sysUpTimeInstance.0

sysContact R/W

sysContact.0

sysName R/W

sysName.0

sysLocation R/W

sysLocation.0

sysServices RO

sysServices.0

sysORLastChange RO

sysORLastChange.0

sysORID RO

sysORID.1

sysORDescr RO

sysORDescr.1

sysORUpTime RO

sysORUpTime.1

1.2. interfaces group

MIB object

Access

Identifier

ifNumber RO

ifNumber.0

ifIndex RO

ifIndex.<port_num>

ifDescr RO

ifDescr.<port_num>

ifType RO

ifType.<port_num>

ifMtu RO

ifMtu.<port_num>

Shows the size without a header
(1500 bytes).

ifSpeed RO

ifSpeed.<port_num>

Shows the maximum port speed
(1 Gbps).

ifPhysAddress RO

ifPhysAddress.<port_num>

ifAdminStatus

R/W

ifAdminStatus.<port_num>

Supports up and down.

ifOperStatus RO

ifOperStatus

<port_num>

ifOLastChange RO

ifOLastChange.<port_num>

ifInOctets RO

ifInOctets.<port_num>

ifInUcastPkts RO

ifInUcastPkts.<port_num>

ifInNUcastPkts RO

ifInNUcastPkts.<port_num>

ifInDiscards RO

ifInDiscards.<port_num>

ifInErrors RO

ifInErrors.<port_num>

ifInUnknownProtos RO

ifInUnknownProtos.<port_num>

ifOutOctets RO

ifOutOctets.<port_num>

ifOutUcastPkts RO

ifOutUcastPkts.<port_num>

ifOutNUcastPkts RO

ifOutNUcastPkts.<port_num>

ifOutDiscards RO ifOutDiscards.<port_num>

ifOutErrors RO

ifOutErrors.<port_num>

ifOutQLen RO

ifOutQLen.<port_num>

ifSpecific RO

ifSpecific.<port_num>

Summary of Contents for PN28160A






















































































































































































































































































Search results

Summary of Contents for PN28160A

Reviews:

Related manuals for PN28160A

Brands by name

Popular brands

Panasonic PN28160A, Operation Manual

Search results

Summary of Contents for PN28160A

Reviews:

Related manuals for PN28160A

Brands by name

Popular brands