background image

37

Helpful Hints

If a clear picture is not produced, insert a
commercially available cleaning cassette.
Then, press 

REC 

¥

 

(

¥

 REC/OTR)

 and keep it

running for approximate 10 seconds to clean
the video heads.
If the problem still persists after performing all
of the measures listed above, contact a service
personnel to request assistance.

Heads mainly become dirty because of
scratched or dirty tapes, use of the unit in
places where temperature and humidity are
high, dust in the air and other reasons.

Never use tapes on which juice has been spilt
or those that are extremely damaged since this
will not only cause the heads to become dirty,
but will also make the unit malfunction.

Dirt on the video heads

If the video heads get dirty, pictures will not be
recorded or played back clearly.
(See the following conditions.)

Normal

picture

Small

amount

of dirt

Large

amount

of dirt

If this happens, insert and eject a cassette
5–10 times in a row to remove the dirt
from the video heads.

CVC (Crystal View Control)
Indicator

The crystal view control function ensures that
you always obtain the optimum picture quality
so that you get the best picture automatically.
While the VCR is turned on, the CVC indication
is always displayed to show that the Crystal
View Control is activated.

Longrun Head System

This longrun head system enables
approximately 8,000 hours of recording/
playback with high quality images. Newly
developed head cylinder with narrower head
windows and tapered cylinder design
effectively protects heads from dust and
prevents head clogging. Plus, “Alumina” Head
Cleaner further enhanced cleaning efficiency.

Based on in-house tests with Panasonic
video cassettes. Actual head life may vary
according to conditions of use, tape type,
temperature, humidity, etc.

The serial number of this product can be
found on the rear panel. No others have the
same serial number as yours. You should
record the number and other vital
information here and retain this book as a
permanent record of your purchase to aid
identification in case of theft.

Date of Purchase

Dealer purchased from

Dealer Address

Dealer Phone No.

Model No.

AG-1350P

Serial No.

Surge Absorber

For added protection for this product, these
models are equipped with new surge absorbing
circuit which prevents damage due to power
surges caused by induced lightning.

This function may not be effective for surges
by direct lightning.

Summary of Contents for ProLine AG-1350









































Reviews: