[POSITION] menu
ENGLISH
- 61
Settings
[ASPECT]
You can switch the image aspect ratio manually when
needed.
Aspect ratio depends on signals.
Switch settings
Switch settings
■
When a VIDEO/S-VIDEO signal is input
[NTSC/NTSC4.43/PAL-M/PAL60 input]
[AUTO]
[4:3]
[16:9]
[ZOOM]
[JUST]
[S16:9]
Note
z
[AUTO] is enabled only when an NTSC signal is input for
both VIDEO and S-VIDEO signals.
[PAL/PAL-N/SECAM input]
[16:9]
[S16:9]
[14:9]
[ZOOM1]
[4:3]
[JUST]
[ZOOM2]
■
When a COMPUTER (RGB) signal is
input
[4:3]
[16:9]
Note
z
If using a 1 280 × 720/60, 1 280 × 768/60, 1 280 x
800/60, WXGA+60, 1 920 x 1 080/50, 1 920 x 1 080/60,
or WUXGA60RB signal, the aspect ratio is fixed so this
cannot be switched.
■
HDMI
[1 080/60i, 1 080/50i, 1 080/60p, 1 080/50p,
1 080/24p, 720/60p, 720/50p input]
[16:9]
[S16:9]
[H-FIT]
[4:3]
[ZOOM]
[V-FIT]
[480p input]
[16:9]
[S16:9]
[JUST]
[4:3]
[ZOOM]
[576p input]
[16:9]
[S16:9]
[14:9]
[ZOOM1]
[4:3]
[JUST]
[ZOOM2]
■
COMPONENT signal (YC
B
C
R
/YP
B
P
R
) /
COMPUTER (RGB) signal
[1 080/60i, 1 080/50i, 1 080/60p, 1 080/50p,
1 080/24p, 720/60p, 720/50p input]
[16:9]
[S16:9]
[H-FIT]
[4:3]
[ZOOM]
[V-FIT]
[480i/480p input]
[AUTO]
[4:3]
[16:9]
[ZOOM]
[JUST]
[S16:9]
[576i/576p input]
[16:9]
[S16:9]
[14:9]
[ZOOM1]
[4:3]
[JUST]
[ZOOM2]
Attention
z
If a 4:3 aspect video is projected at a 16:9 aspect ratio,
the edges may not be visible or the shape of the image
may change. Please project videos intended by the
author for 4:3 projection at that aspect ratio.
Note
z
If an aspect ratio that differs from the one used in the
input signal is selected, the video will look different from
the original.
z
If you project a copyrighted image enlarged or distorted
by using [ASPECT] function in commercial use in a
public place, such as a restaurant or hotel, you might
infringe on the copyright of the creator which is protected
by copyright law.
z
When set to [AUTO], the aspect ratio is automatically
switched to the optimum aspect ratio when an aspect
ratio identifier is included in the input signal.
z
[AUTO] may not be displayed if the input signal is VIDEO
or COMPONENT (YC
B
C
R
/YP
B
P
R
).
z
A black area may appear at the top and bottom of the
screen when videos that are wider than 16:9 (cinema
vision etc.) are projected.
z
When a signal is input that uses overseas broadcasting
formats, the supported aspect ratio modes differ from the
table shown.
z
When a 3D signal is input
*1
, other than for [S16:9], the
aspect ratio set for 2D signal input is not maintained and
16:9 is used for display. When a 3D signal is input the
[ASPECT] setting cannot be switched.
*1 Only when [2D TO 3D] for [3D SETTINGS] menu is set to
[OFF]
Downloaded From projector-manual.com Panasonic Manuals
