ENGLISH - 79
Chapter 4 Settings — [PROJECTOR SETUP] menu
9)
Press
qw
to switch [COMMAND].
r
f
The setting will change among [POWER ON], [STANDBY],
[SHUTTER]
*1
, [INPUT]
*1
, [LAMP SELECT]
*1
, [LAMP POWER]
*1
and [SIDE BY SIDE]
*1*2
each time you press the button.
*1
The details set in step
11)
are displayed.
*2
Only for PT-DW740E
10)
Press the <ENTER> button.
r
f
The
[COMMAND]
detailed screen is displayed.
11)
Press
as
to select a command.
r
f
[OPEN]/[CLOSE] in [SHUTTER], [RGB1]/[RGB2]/[VIDEO]/
[S-VIDEO]/[DVI-D]/[HDMI] in [INPUT], [DUAL]/[SINGLE] in
[LAMP SELECT], [NORMAL]/[ECO] in [LAMP POWER], and
[OFF]/[ON] in [SIDE BY SIDE] will change each time you press
qw
.
12)
Press the <ENTER> button.
r
f
The command is fixed and ● is displayed at the left of the
selected command.
r
f
After the command is fixed, press the <MENU> button to close
the detailed setting menu.
13)
Press
as
to select [STORE], and press the
<ENTER> button.
r
r
[COMMAND]
[POWER ON]
―
Turns the power on.
[STANDBY]
―
Enters standby.
[SHUTTER]
[OPEN]
Opens the shutter.
[CLOSE]
Closes the shutter.
[INPUT]
[RGB1]
Switches the input to RGB1.
[RGB2]
Switches the input to RGB2.
[VIDEO]
Switches the input to VIDEO.
[S-VIDEO]
Switches the input to S-VIDEO.
[DVI-D]
Switches the input to DVI-D.
[HDMI]
Switches the input to HDMI.
[LAMP SELECT]
[DUAL]
Turns on both lamps.
[SINGLE]
Turns on one lamp. (The lamp is automatically selected which has shorter
cumulative operating time.)
[LAMP POWER]
[NORMAL]
Sets the high luminance of the lamp.
[ECO]
Sets lower luminance of the lamp than [NORMAL].
[SIDE BY SIDE]
*
[OFF]
Displays the side-by-side screen.
[ON]
Cancels the side-by-side screen.
*
Only for PT-DW740E
Note
r
f
If you try to register a setting that would cause the lamp to flash for a short time, an error message will be displayed on the screen. Set the
time and command again.
r
f
To delete a command already set, press the <DEFAULT> button on the Step
5)
screen, or select [DELETE] on the Step
6)
screen and press
the <ENTER> button.
r
f
If multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command
number.
r
f
The operating time will be the local time. (
x
page 83)
r
f
If an operation is executed with the remote control or control panel of the projector or with a control command before the command set in
[SCHEDULE] is executed, the command set with this function may not be executed.
[STARTUP INPUT SELECT]
Set the input signal to be projected when the projector is switched on.
1)
Press
as
to select [STARTUP INPUT
SELECT].
2)
Press
qw
to switch [STARTUP INPUT
SELECT].
r
f
The setting will change among [LAST USED], [RGB1], [RGB2],
[VIDEO], [S-VIDEO], [DVI-D] and [HDMI] each time you press
the button.
r
r
[STARTUP INPUT SELECT]
[LAST USED]
Keeps the input selected last.
[RGB1]
Sets the input to be projected when the projector is switched on to RGB1.
[RGB2]
Sets the input to be projected when the projector is switched on to RGB2.
[VIDEO]
Sets the input to be projected when the projector is switched on to VIDEO.
