Chapter 4
Settings — [PROJECTOR SETUP] menu
ENGLISH - 117
7) Press
qw
to select “hour” or “minute”, and press
as
or the number (<0> - <9>) buttons to set a
time, and then press the <ENTER> button.
8) Press
asqw
to select [COMMAND].
9) Press the <ENTER> button.
f
The
[COMMAND]
detailed screen is displayed.
10) Press
as
to select a [COMMAND].
f
For [COMMAND] which requires detailed settings, the items of the detailed settings will switch each time you press
qw
.
f
When [INPUT] is selected, press the <ENTER> button, and then press
asqw
to select the input to set.
[COMMAND]
Detailed settings of
[COMMAND]
Description
[POWER ON]
―
Switches on the projector.
[STANDBY]
―
Enters standby.
[SHUTTER]
[OPEN]
Opens the shutter.
[CLOSE]
Closes the shutter.
[INPUT]
[VIDEO]
Switches the input to VIDEO.
[RGB1]
Switches the input to RGB1.
[RGB2]
Switches the input to RGB2.
[DVI-D]
Switches the input to DVI-D.
[HDMI]
Switches the input to HDMI.
[DIGITAL LINK]
Switches the input to DIGITAL LINK.
[SDI]
*1
Switches the input to SDI.
[INPUT1] - [INPUT10]
*2
Switches the input to DIGITAL LINK, and switch the input of the
Panasonic twisted-pair-cable transmitter to the specified input.
[LAMP SELECT]
[DUAL]
Turns on two lamps.
[SINGLE]
Turns on one lamp. (The lamp with shorter runtime will
automatically light.)
[LAMP POWER]
[NORMAL]
Sets the lamp brightness to high luminance.
[ECO]
Sets the lamp brightness to low luminance.
[P IN P]
[OFF]
P IN P function is not used.
[USER1]
Lays out the sub-screen with the settings of [USER1].
[USER2]
Lays out the sub-screen with the settings of [USER2].
[USER3]
Lays out the sub-screen with the settings of [USER3].
*1
Only for PT-DZ870E
*2
When the Panasonic twisted-pair-cable transmitter (such as the optional Digital Interface Box (Model No.: ET-YFB100G)) is connected to the
projector, its input name is reflected from [INPUT1] to [INPUT10] automatically. If an item where the input name is not reflected is selected, it
is disabled.
11) Press the <ENTER> button.
f
The command is fixed and
n
is displayed at the left of the selected command.
f
After the command is fixed, press the <MENU> button to close the detailed setting screen.
12) Press
asqw
to select [STORE], and press the <ENTER> button.
Note
f
If you attempt to register the setting that would make the lamp turn on for a short time, an error message will be displayed on the screen.
Set the time and command again.
f
To delete a command already set, press the <DEFAULT> button on the remote control at the screen in Step
5)
, or select [DELETE] at the
screen in Step
6)
and press the <ENTER> button.
f
If multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command
number.
f
The operating time will be the local time. (
x
page 121)
f
If an operation is executed with the remote control or control panel of the projector or with a control command before the command set in
[SCHEDULE] is executed, the command set with this function may not be executed.
[STARTUP INPUT SELECT]
Set the input when the projector is switched on to start projection.
1) Press
as
to select [STARTUP INPUT SELECT].
2) Press the <ENTER> button.
f
The
[STARTUP INPUT SELECT]
screen is displayed.
