Timer Recording
*
Important:
If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
- 7 -
Timer Recording
1
Press PROG*
to display program screen.
Press PROG
to end programming.
2
3) Set remaining items,
press
to set START/ STOP times, CH (channel) or
LINE input (p. 9 of Advanced Operations book), and
tape speed (p. 3).
Then
press
to select.
1) Press
.
2) Set record DATE,
press
to select:
1~31= one time,
or DAILY= Monday~Friday,
or WEEKLY= same time
each week (see right).
3
To Enter More Programs
Press
to select and
press
to set an unused program.
Then repeat step 2. Or,
press PROG
to exit.
Timer Recording
Press
to select
desired program.
4
Press POWER off
to set the timer recording. (“TIMER” lights on Multi Function Display.)
(Recording is not in progress)
a
Press PROG
to display program screen.
b
c
To Replace program...
d
Press PROG
to end the programming.
• If you are using a Cable Box, VCR Timer Programming Channel (Step 2 above) must be set to the
Cable Box output channel and your Cable Box must be manually set to the desired channel.
The Cable Box must be left on.
• If a power interruption occurs while programming the timer, the timer program(s) may be cancelled.
If “TIMER PROGRAMS WERE LOST DUE TO POWER INTERRUPTION” appears on-screen,
please re-enter the timer programs.
Important notes when using DSS receiver
• When recording programs via DSS receiver, DSS receiver must be left on.
• When recording programs via an antenna or cable, DSS receiver must be turned off.
Review, Replace, or Clear Program
1) Press
to display.
2)
Repeat Step 2
(p. 6) to set new
programs.
Press ADD/DLT
.
or
To Clear program...
Press POWER
and then
STOP
within 10
seconds to cancel the Timer Recording.
(The TIMER indicator goes out on Multi
Function Display.)
Cancel a Timer Recording
(Recording is in progress)
- 6 -
Notes
P DT START STOP CH SPD
1 13 2:00p 3:20p 02 SLP
2 14 7:00p 7:30p 10 SP
3 -- --:-- --:-- -- --
4 -- --:-- --:-- -- --
SELECT : SET :
EXIT
: PROG
P DT START STOP CH SPD
1
13 2:00p 3:20p 02 SLP
2 -- --:-- --:-- -- --
3 -- --:-- --:-- -- --
4 -- --:-- --:-- -- --
CANCEL : ADD/DLT
SELECT : SET :
END
: PROG
SET COMPLETED
P DT START STOP CH SPD
1
-- --:-- --:-- -- --
2 -- --:-- --:-- -- --
3 -- --:-- --:-- -- --
4 -- --:-- --:-- -- --
SELECT : SET :
END
: PROG
P DT START STOP CH SPD
1
-- --:-- --:-- -- --
2 14 7:00p 7:30p 10 SP
3 -- --:-- --:-- -- --
4 -- --:-- --:-- -- --
SELECT : SET :
END
: PROG
*
Important:
If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
- 5 -
1
Insert a tape
.
Record on a Tape
Playback a Tape
Playback / Record on a Tape
Auto Play
Insert a tape
➛
Power comes on
➛
Play starts if there is no record tab (see p. 3).
Auto Rewind
Play
Fast Forward
Play Auto Eject
(Repeat Play must be off)
Play
➛
Tape end
➛
Rewind
➛
Stop
➛
Tape ejects if there is no record tab.
Auto Operation Functions
➛
Tape end
➛
Rewind
➛
Stop
Connections / Initial Setup (Ready to Play)
Connecting (Select a method)
Connect cable from
Antenna/Cable to VCR’s IN
FROM ANT. jack.
Connect VCR’s OUT TO TV
jack to TV’s ANT. IN jack
with included RF Cable.
For ANT./Cable
➛
➛
➛
➛
➛
VCR
➛
➛
➛
➛
➛
TV
For DSS/Cable Box
➛
➛
➛
➛
➛
VCR
➛
➛
➛
➛
➛
TV
Connect your cable box’s OUT
jack to the VCR’s IN FROM
ANT. jack with an RF cable.
Connect VCR’s OUT TO TV
jack to TV’s ANT. IN jack with
included RF Cable.
1
2
1
2
Make all cable or antenna connections before plugging into an AC outlet.
Plugging the VCR Power Cord into an AC wall outlet starts auto channel and clock set.
If you use a cable box, turn it on and set it to the
Public Broadcasting Station (PBS) channel in
your time zone. If you use a DSS receiver, it
must be turned off.
3
Settings are made automatically.
When complete, this screen appears.
If “AUTO CLOCK SET IS INCOMPLETE”
appears, manually set clock (below).
Manual Clock Set
If Auto Clock Set was incomplete.
1
Press ACTION* on remote to display
CLOCK menu.
2
Press to select the month and to set.
In the same manner, select and set the
date, year, time, and DST (Daylight Saving
Time).
3
Press ACTION to start clock and exit.
- 4 -
Congratulations
on your new purchase! With proper use, this
dependable product will provide years of
enjoyment. Please fill in the information below.
(Serial number is on tag on back of VCR.)
Before Using
• Date of Purchase
• Dealer Purchased From
• Dealer Address
• Dealer Phone No.
• Model No.
PV-V4535S-K
• Serial No.
Head Cleaning
• Important Safeguards
• Accessor
ies
• Head Cleaning
• Loading Batteries
• Pr
e
v
ent
T
a
pe Erasur
e
• Specif
ications
• Record/Playback
T
ime
- 3 -
Video Head Clog Sensor
Screen-right appears during
play if clogging is detected.
To remove screen, press PLAY.
• Use “dry” type head
cleaning cassette only.
(Part No. NV-TCL30PT is recommended.)
• Follow cleaning tape instructions carefully.
Excessive use of tape can shorten head life.
• If head clog symptoms persist, contact your
nearest Factory Servicentre or authorized
Servicentre (p. 12).
Old or damaged tapes may clog heads.
V I DEO HEADS MAY
NEED CLEAN I NG
PLEASE I NSERT HEAD
CLEAN I NG CASSETTE
OR REFER TO MANUAL
END : PLAY
- 2 -
AUTO CLOCK SET
IS I NCOMPLETE
PLEASE SET CLOCK BY
PRESSING ACT I ON KEY
• Function buttons are void during Initial Setup.
• To eject a tape during Auto Set, press EJECT
on remote or STOP twice on VCR.
Then make settings manually. (See p. 11.)
• If Auto Clock Set takes more than 30 minutes,
press STOP and perform settings manually.
(See p. 11.)
Notes
P DT START STOP CH SPD
1
13 2:00p 3:20p 02 SLP
2 14 7:00p 7:30p 10 SP
3 -- --:-- --:-- -- --
4 -- --:-- --:-- -- --
CANCEL : ADD/DLT
SELECT : SET :
END
: PROG
• Connections
• Initial
Setup
• Clock Set
• Select
Channel
• Playback
• Record
• A
uto Operation
Loading the Batteries
Battery replacement caution
• Do not mix old and new batteries.
• Do not mix alkaline with manganese batteries.
1) Open cover.
3) Close cover.
2) Insert batteries as
marked.
Only use tapes with the
mark in this unit.
Record/Playback Time
SP
(Standard Play)
2 Hours
40 Minutes
2 Hours
6 Hours
8 Hours
SLP
(Super Long Play)
Type of Video Cassette
Tape Speed
Setting
T180
T160
T120
3 Hours
9 Hours
Digital Auto Picture
Automatically controls the video output signal for
less noise depending on the tape condition.
Digital Auto Tracking
Continuously analyzes the signal and adjusts for
optimum picture quality.
Manual Tracking Control
(to reduce picture noise)
Use during Playback and Slow Motion mode to
reduce picture noise.
Press CH
(TRACKING) / on the remote
control or on the VCR until the picture clears up.
To return to Auto Tracking,
press POWER
off,
then on again a few seconds later.
V-Lock Control (to reduce picture jitter)
In Still mode,
CH
(TRACKING) / operate as a
V-Lock control.
Features for a Quality Picture
R
R
R
R
R
R
R
R
Use soft, dry cloth or dusting attachment of a
vacuum to remove dust from all cabinet vent
holes. You may moisten cloth with non-abrasive,
antistatic cleaner/ polisher.
Caution
:
Alcohol and various solvents could damage finish.
Cleaning the VCR
• T
imer Recor
ding
Note: Designs and specifications are subject to
change without notice.
Power Source:
120 V AC, 60 Hz
Power Consumption:
Power On
Approx. 14 W
Power Off
Approx. 0.9 W
Video Signal:
EIA Standard NTSC colour
Video Recording
4 rotary heads helical
System:
scanning system
Audio Track:
1 track (Normal)
2 channel (Hi-Fi Audio Sound)
Tuner
Broadcast Channels:
VHF 2 ~ 13, UHF 14 ~ 69
CABLE Channels:
Midband A ~ I (14 ~ 22)
Superband J ~ W (23 ~ 36)
Hyperband AA ~ EEE
(37 ~ 64)
Lowband A-5 ~ A-1 (95 ~ 99)
Special CABLE channel 5A (01)
Ultraband 65 ~ 94, 100 ~ 125
Operating
Temperature:
5 °C ~ 40 °C (41 °F ~ 104 °F)
Operating Humidity:
10 % ~ 75 %
Weight:
2.56 k
g
(5.6 lbs.)
Dimensions:
360 (W) x 89 (H) x 226 (D) mm
14-3/16” (W) x 3-1/2” (H) x
8-7/8” (D) inch
Specifications
Initial Setup (Ready to Play)
1
Turn TV on and tune to channel 3.
2
Plug VCR Power Cord into AC wall outlet.
VCR comes on and SELECT LANGUAGE
screen appears. When one of “1”, “2”, “3”
keys is pressed, auto channel and clock set
starts.
• If screen below does not appear...
check all connections.
Try tuning TV to channel 4.
• To change VCR’s output channel, please
refer to “VCR’s Output Channel” (p. 11).
• If wrong language is set, do “Reset All VCR
Memory Functions” (p. 10).
Plug VCR Power plug into an AC wall outlet.
Select language
Press 1
: English
Press 2
: French
Press 3
: Spanish
AUTO CLOCK SET
PROCEEDING
CANCEL : STOP
CH AUTO SET PROCEEDING
CANCEL : STOP
SELECT LANGUAGE
ENGL I SH
:PRESS
1
FRANÇA I S
:APPUYER
2
ESPAÑOL
:OPR I M I R
3
RF Coaxial Cable
LSJA0418
Batteries 2 “AA”
Remote Control
EUR7723KC0
Accessories
Prevent Accidental Tape Erasure
To record again.
Break off the tab to
prevent recording.
Record Tab
Screw driver
Cover the hole
with cellophane
tape.
Over tightening “Nut type” RF coaxial cables
may damage jacks. Finger tighten only.
Important Safeguards and Precautions
TO REDUCE THE RISK OF ELECTRIC SHOCK, FIRE, INJURY TO PERSONS OR DAMAGE TO
THIS PRODUCT, READ AND RETAIN ALL SAFETY AND OPERATING INSTRUCTIONS. HEED ALL
WARNINGS IN THE MANUAL AND ON THE PRODUCT.
INSTALLATION
1 POWER SOURCE CAUTION
Operate only from a power source indicated on the unit
or in this manual. If necessary, have your Electric Utility
Service Company or Video Products Dealer verify the
power source in your home.
2 POLARIZED OR GROUNDING PLUG
As a safety feature, this Video product comes with
either a polarized power cord plug (one blade is wider
than the other), or a three-wire grounding type plug.
POLARIZED PLUG CAUTION:
This plug will only fit into an outlet one way. If you cannot
fully insert the plug, try reversing it. If it still will not fit,
have an electrician install the proper wall outlet. Do not
defeat the safety feature by tampering with the plug.
GROUNDING PLUG CAUTION:
This plug will only fit into a three-hole grounding outlet.
If necessary, have an electrician install the proper outlet.
Do not defeat the safety feature by tampering with the plug.
3 POWER CORD
Make sure power cords are routed so that they are not
likely to have anything rest on them, roll over them, or
be in the way of walking traffic. If an extension cord is
used, make sure it also has either a polarized or
grounded plug and that the cords can be securely
connected. Frayed cords, damaged plugs, and damaged
or cracked wire insulation are hazardous and should be
replaced by a qualified service technician.
Overloaded outlets and extension cords are fire hazards
and should be avoided.
4 DO NOT BLOCK VENTILATION HOLES
Ventilation openings in the cabinet release heat
generated during operation. If they are blocked, heat
build-up inside the unit can cause failures that may
result in a fire hazard or heat damage to cassettes.
For protection, follow these rules:
a. Never cover ventilation slots or the unit while in use,
or operate the unit when placed on a bed, sofa, rug,
or other soft surface.
b. Avoid built-in installation, such as a book case or
rack, unless proper ventilation is provided.
5 AVOID EXTREMELY HOT LOCATIONS OR SUDDEN
TEMPERATURE CHANGES
Do not place the unit over or near any kind of heater or
radiator, in direct sunlight, inside a closed vehicle, etc..
Do not move the unit suddenly between areas of
extreme temperature variation. If the unit is suddenly
moved from a cold place to a warm place, moisture may
condense in the unit and on the tape.
6 TO AVOID PERSONAL INJURY
• Do not place unsecured equipment on a
sloping surface.
• Do not place this unit on any support
that is not firm, level, and adequately
strong. The unit could fall causing
serious injury to a child or adult and
damage to the unit.
• An appliance and cart combination should be moved
with care. Quick stops, excessive force, and uneven
surfaces may cause the appliance and cart
combination to overturn.
• Carefully follow all operating instructions and use the
manufacturer's recommended accessories when
operating this unit or connecting it to any other
equipment.
USING THE VIDEO UNIT
If the unit has been in storage or moved to a new location, refer
first to the INSTALLATION section of these safeguards.
1
KEEP THIS VIDEO UNIT AWAY FROM WATER OR
MOISTURE OF ANY KIND.
2
IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR
STRONG IMPACT,
unplug the unit and have it inspected by
a qualified service technician before use.
3
DURING AN ELECTRICAL STORM
During a lightning storm, whether indoors or outdoors, or
before leaving the unit unused for extended periods of time,
disconnect all equipment from the power source as well as
the antenna and cable system.
4
WHEN THE UNIT IS PLUGGED IN
• Never expose the unit to rain or water. DO NOT OPERATE
if liquid has been spilled into the unit. Immediately unplug
the unit, and have it inspected by a service technician.
Fire and shock hazards can result from electrical shorts
caused by liquid contact inside.
• Never drop or push any object through openings in the
unit. Some internal parts carry hazardous voltages and
contact can cause electric shock or fire hazard.
• Avoid placing the unit directly above or below your TV set
as this may cause electrical interference.
Keep all magnets away from electronic equipment.
5
USING ACCESSORIES
Use only accessories recommended by the manufacturer to
avoid risk of fire, shock, or other hazards.
6
CLEANING THE UNIT
Unplug the unit. Then, use a clean, dry, chemically untreated cloth
to gently remove dust or debris. DO NOT USE cleaning fluids,
aerosols, or forced air that could over-spray, or seep into the unit
and cause electrical shock. Any substance such as wax,
adhesive tape, etc. may mar the cabinet surface. Exposure to
greasy, humid, or dusty areas may adversely affect internal parts.
SERVICE
1
DO NOT SERVICE THIS PRODUCT YOURSELF
If, after carefully following the detailed operating
instructions, this Video product does not operate properly,
do not attempt to open or remove covers, or make any
adjustments not described in the manual. Unplug the unit
and contact a qualified service technician.
2
IF REPLACEMENT PARTS ARE REQUIRED
Make sure the service technician uses only parts specified by
the manufacturer, or those having the same safety
characteristics as the original parts. The use of unauthorized
substitutes may result in fire, electric shock, or other hazards.
3
HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK
After any service or repairs to the unit, request the service
technician to conduct a thorough safety check as described
in the manufacture’s service literature to ensure that the
video unit is in safe operating condition.
OUTDOOR ANTENNA INSTALLATION
1
SAFE ANTENNA AND CABLE CONNECTION
If an outside antenna or cable system is connected to the
equipment, be sure the antenna or cable system is grounded
so as to provide some protection against built up static
charges and voltage surges. Part 1
of the Canadian Electrical Code, in
USA Section 810 of the National
Electrical Code, ANSI/NFPA 70,
provides information with respect to
proper grounding of the mast and
supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size
of grounding conductors, location of antenna discharge unit,
connection to grounding electrodes and requirements for the
grounding electrode.
2
KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR CIRCUITS
An outside antenna system should be located well away from
power lines, electric light or power circuits and where it will never
come into contact with these power sources if it should happen
to fall. When installing an outside antenna, extreme care should
be taken to avoid touching power lines, circuits or other power
sources as this could be fatal. Because of the hazards involved,
antenna installation should be left to a professional.
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC - NATIONAL
ELECTRICAL CODE
This symbol warns the user that uninsulated voltage within the unit may
have sufficient magnitude to cause electric shock. Therefore, it is
dangerous to make any kind of contact with any inside part of this unit.
This symbol alerts the user that important literature concerning the
operation and maintenance of this unit has been included.
Therefore, it should be read carefully in order to avoid any problems.
Safety Precautions
To prevent fire or shock hazard, do not expose this equipment to rain or moisture.
To prevent electric shock, match wide blade of plug to wide slot, fully insert.
FCC WARNING :
Any unauthorized changes or modifications to this
equipment would void the user’s authority to operate.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
2
Press PLAY
to play tape.
• If tape has no rec. tab (p. 3), auto play begins.
•
Loose or peeling labels
may cause tape jam.
• VCR power comes on.
If Auto VCR/TV (see p. 10 of
Advanced Operations book) is set to
“OFF,” press VCR/TV.
1
Insert a tape with a record tab
(p. 3).
2
Press CH
or NUMBER keys
to select the channel.
• If channel number is over 100, first press 100
key then the other 2 digits.
• For “LINE” input, see p. 9 of “Advanced
Operations” book.
3
Press SPEED
to set record speed (p. 3).
4
Press REC
to start recording.
• To edit,
press PAUSE/SLOW
to pause, and
again to resume recording.
5
Press STOP
to stop recording.
One Touch Recording
(recording in progress)
Press REC
repeatedly to set length as follows:
30 min.
➛
1 hr.
➛
1:30
➛
2:00
➛
3:00
➛
4:00
➛
exit.
The VCR shuts off at the length set.
Record one station, watch another
Press VCR/TV
➛
select channels on TV (recording continues).
Select channels on VCR
Press VCR/TV
in Stop or Pause mode.
➛
select channels on VCR.
• Watching one channel and recording
another is not possible when using Cable
Box or DSS Receiver.
• After 5 minutes in Pause mode, VCR stops to
protect the tape and the video heads.
• VCR power comes on.
If Auto VCR/TV (see p. 10 of Advanced
Operations book) is set to “OFF,” press
VCR/TV.
Notes
• SP = Standard Play
• SLP = Super Long Play
This video recorder, equipped with HQ
(High Quality) system, is compatible with
existing VHS equipment. Only use tapes
with the
mark. Only tapes tested and
inspected for use in 2, 4, 6, and 8 hour
machines are recommended.
Example
Today
Special Features During Play
Still (Freeze) Picture
➛
Press PAUSE/SLOW
.
➛
Press PLAY
to release.
Slow Motion Picture
➛
Hold down PAUSE/SLOW
in Still mode.
➛
Press PLAY
to release.
• These features work best in SP or SLP mode.
• The sound will be muted.
• To reduce picture noise, see “Manual
Tracking Control” on p. 3.
• After 3 minutes in Still or Slow mode, VCR
stops to protect the tape and the video heads.
Rapid Rewind/FF
Press REW or FF
in Stop
mode
to
rewind or fast forward tape.
Press EJECT
on remote,
or
STOP/EJECT
on VCR to eject tape.
3
Press STOP
to stop tape.
• Picture interruption may occur with some TVs.
• FF and REW search speed may vary depending
on current tape position.
• After 10 minutes in search mode, VCR returns to
Play mode to protect the tape and the video
heads.
Notes
Notes
• Rewinds a T-120 tape in approx. 1 minute.
Forward/Reverse Scene Search
➛
Press FF
or
REW
.
➛
Press PLAY
to release.
After search has begun, each additional
press of
FF
or
REW
changes speed as
shown below.
[SP] : Approx. 9X
↔
Approx. 13X
[SLP] : Approx. 27X
↔
Approx. 43X
1
2
2
1
V4535S-K (E) Basic-2 (041209).p65
2004/12/13, 9:59
3
LSQT0926A (Basic Operations) - Back
