Panasonic RAMSA WS-AT300 Operating Instructions Manual Download

Page: 1 / 12

Speaker System

WS-AT300

Subwoofer System

WS-AT350

Before attempting to connect or operate this product, please read these instructions completely

CONTENTS

REGULATORY STATEMENTS .............................................................................. 2

SAFETY INSTRUCTIONS ...................................................................................... 2

PREFACE .............................................................................................................. 3

PRECAUTIONS ..................................................................................................... 3

INSTALLING THE SPEAKER ................................................................................ 4

CONNECTING SPEAKER CABLES ..................................................................... 6

WIRING CONNECTOR AND CABLE .................................................................... 7

SETTING THE SUBWOOFER PROCESSOR ......................................................... 8

PROTECTION CIRCUITS FOR WS-AT300 ............................................................ 8

BLOCK DIAGRAM ................................................................................................ 9

SPECIFICATIONS ................................................................................................. 9

TYPICAL PERFORMANCE .................................................................................. 10

DIRECTIVITY ....................................................................................................... 10

APPEARANCE .................................................................................................... 11

WS-AT300

WS-AT350

Summary of Contents for RAMSA WS-AT300













Search results

Summary of Contents for RAMSA WS-AT300

Reviews:

Related manuals for RAMSA WS-AT300

Brands by name

Popular brands

Panasonic RAMSA WS-AT300, Operating Instructions Manual

Search results

Summary of Contents for RAMSA WS-AT300

Reviews:

Related manuals for RAMSA WS-AT300

Brands by name

Popular brands