Panasonic RAMSA WS-AT300 Operating Instructions Manual Download

Page: 8 / 12

-8-

SETTING THE SUBWOOFER PROCESSOR

PROTECTION CIRCUITS FOR WS-AT300

SYSTEM DIAGRAM

Audio

Mixer

WS-SP2A

Subwoofer
Processor

In A

In B

Amplifier

200W

400W

BTL

400W

BTL

WS-AT300

WS-AT350

-50 -

-40

-50 -

-40

• The WS-AT300 has separate overload protection
circuits for woofer and tweeter. When activated by an
excessive input signal, they mute the output sound.
Turn down the volume control for 2 to 20 seconds to
reset the circuits.

VLFI

WS-AT350

SUB WOOFER

MAIN SPEAKER

RECOMMENDED FUNCTION SE

CTOR SETTING

FUNCTION SELECTOR POSITION

WS-AT300

For further details please refer to the Operating Instructions of the RAMSA Subwoofer Processor WS-SP2A.

Note:

Make sure to lower the volume control of the

amplifiers if the output sound suddenly decreases.
Keeping or even increasing the volume can cause
serious damage to the speaker.

This shows an example of system connections.

Summary of Contents for RAMSA WS-AT300













Search results

Summary of Contents for RAMSA WS-AT300

Reviews:

Related manuals for RAMSA WS-AT300

Brands by name

Popular brands

Panasonic RAMSA WS-AT300, Operating Instructions Manual

Search results

Summary of Contents for RAMSA WS-AT300

Reviews:

Related manuals for RAMSA WS-AT300

Brands by name

Popular brands