background image

2

RQT0A04

Safety precautions

Unit

To reduce the risk of fire, electric shock or 
product damage,

j

Do not expose this unit to rain, moisture, 
dripping or splashing.

j

Do not place objects filled with liquids, such as 
vases, on this unit.

j

Use only the recommended accessories.

j

Do not remove covers.

j

Do not repair this unit by yourself. Refer 
servicing to qualified service personnel.

To prevent injury, this apparatus must be 
securely attached to the wall in accordance with 
the installation instructions.

AC mains lead

To reduce the risk of fire, electric shock or 
product damage,

j

Ensure that the power supply voltage 
corresponds to the voltage printed on this unit.

j

Insert the mains plug fully into the socket outlet.

j

Do not pull, bend, or place heavy items on the 
lead.

j

Do not handle the plug with wet hands.

j

Hold onto the mains plug body when 
disconnecting the plug.

j

Do not use a damaged mains plug or socket 
outlet.

The mains plug is the disconnecting device.
Install this unit so that the mains plug can be 
unplugged from the socket outlet immediately.

Button-type battery (Lithium battery)

Risk of fire, explosion and burns. Do not 
recharge, disassemble, heat above 60

o

C or 

incinerate.

Keep the Button-Type battery out of the reach of 
children. Never put Button-Type battery in 
mouth. If swallowed call your doctor.

Small object

Keep the screws out of reach of children to 
prevent swallowing.

Keep the adhesive tape out of reach of children 
to prevent swallowing.

Keep the button-type battery out of reach of 
children to prevent swallowing.

Unit

Do not place sources of naked flames, such as 
lighted candles, on this unit.

This unit may receive radio interference caused 
by mobile telephones during use. If such 
interference occurs, please increase separation 
between this unit and the mobile telephone.

This unit is intended for use in moderate 
climates.

Product Identification Marking is located on the 
bottom of the unit.

Placement

Place this unit on an even surface.

To reduce the risk of fire, electric shock or 
product damage,

j

Do not install or place this unit in a bookcase, 
built-in cabinet or in another confined space. 
Ensure this unit is well ventilated.

j

Do not obstruct this unit’s ventilation openings 
with newspapers, tablecloths, curtains, and 
similar items.

j

Do not expose this unit to direct sunlight, high 
temperatures, high humidity, and excessive 
vibration.

Button-type battery (Lithium battery)

Danger of explosion if battery is incorrectly 
replaced. Replace only with the type 
recommended by the manufacturer.

Insert with poles aligned.

Mishandling of batteries can cause electrolyte 
leakage and may cause a fire.

j

Remove the battery if you do not intend to use 
the remote control for a long period of time. 
Store in a cool, dark place.

j

Do not heat or expose to flame.

j

Do not leave the battery(ies) in a car exposed 
to direct sunlight for a long period of time with 
doors and windows closed.

When disposing of the batteries, please contact 
your local authorities or dealer and ask for the 
correct method of disposal.

WARNING

CAUTION

SC-HTB485-EGEBGN_RQT0A04-B.book  2 ページ  2015年1月22日 木曜日 午前10時15分

Summary of Contents for S-HTB480





































Reviews: