Panasonic S-ics Technical Manual Download

Page: 145 / 327

Section 700 - Operation

Chapter 5. Key Telephone Features

S-ICX-64-700

S-ICX (International) issued April 2002

145

With Version 6.1, if an FF key is assigned as a Caller ID key, the key flashes when Caller ID

information is received and the call is not answered (Busy/No Answer/CFWD/Hunting). This key can

then be pressed to access the Call Log.

Call Log Operation on a Small- and Large-Display Key Telephones

Operation

See

Section 750 - Key Phone User Guide

for operating instructions and Call Log display examples.

Hardware Requirements

Caller ID is typically 10 digits. If the local calling area requires 7-digit dialing, the call log outdialing

will not operate properly.

•

Caller ID daughter circuit card on the Loop Start Exchange Line Card if a Loop Start Exchange

Line receives the call.

•

ISDN (PRI-T Point) if ISDN card receives the call.

•

Large Display Telephone or Small Display Telephone.

Considerations

•

Caller ID is available ISDN PRI.

•

Caller ID circuit card must be installed and enabled. (See “Caller ID” on page 28).

•

Caller ID is typically 10 digits. If the local calling area requires 7-digit dialling, the call log

outdialling will not operate properly.

Camp-on (Call Waiting)

Description

If you dial a busy extension, you can camp onto that extension and send a Call Waiting signal to the

called party. The called party then needs only to replace the handset and pick it up again to be

automatically connected to the new call. The called party can also press the

HOLD

key to place the

first call on hold and then answer the waiting call.
The System provides two types of call waiting:

•

Automatic Call Waiting:

You do not need to enter a code to send the Call Waiting signal to

the busy extension. You need only to remain on the line.

•

Manual Call Waiting:

You must enter a code to send a Call Waiting signal to the busy

extension.

Beginning with CPC Version 3.0, you can leave a text message that displays on the busy phone. Any

one of the following messages can be selected. Messages 6 to 9 and 0 have no default message text.

All the messages can be changed through system programming. (See “Set Text Message Replies” on

page 112 for more information on setting Send Text Messages).

Table 16. Send Text Messages

Message No.

Message Text

Message No.

Message Text

Visitor Here

User Defined

Summary of Contents for S-ics








































































































































































































































































































































Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands

Panasonic S-ics, Technical Manual

Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands