Panasonic S-ics Technical Manual Download

Page: 218 / 327

218

S-ICX (International) issued April 2002

S-ICX-64-700

Chapter 6. DSLT Features

Section 700 - Operation

Code users can “float” from phone to phone, placing calls that would normally be restricted on that

phone.

Non-Verified Account Codes

Non-Verified Account codes are voluntary codes. (i.e., You do not have to enter an account code

before making a call.)
You can assign Non-Verified Account codes to both incoming and outgoing calls. To assign an

account code to an outgoing call, you enter the account code before making the call or during the call.

To assign an account code to an incoming call, you enter the account code during the call.

Operation

To enter an account code before making a call:

To enter an account code during an outside call:

Verified Account Codes

Stations restricted from outside call origination by Toll Restriction Service (TRS) - Call Barring can

be allowed to make outgoing calls by entering a Verified Account code that changes the TRS (Call

Barring). After a call is made, the Call Logging record for the call will show the verified account

code.

Action

Result

1. Lift the handset or press the

ON/OFF

key.

Intercom dial tone

2. Enter the Account Code feature code (default =

3. Enter the Account Code (up to 10 digits).

4. Press the

key.

5. Press a vacant trunk key or enter an exchange line access

code (default = 9 or 81-84).

6. Dial the phone number.

Action

Result

1. During a call, press the

MEMORY

key.

2. Press the

key.

3. Enter the Account Code (up to 10 digits).

4. Press the

key.

Summary of Contents for S-ics








































































































































































































































































































































Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands

Panasonic S-ics, Technical Manual

Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands