Panasonic S-ics Technical Manual Download

Page: 238 / 327

238

S-ICX (International) issued April 2002

S-ICX-64-700

Chapter 6. DSLT Features

Section 700 - Operation

To set Manual Camp-on:

To answer a Camp-on (Call Waiting) signal:

Hardware Requirements

•

N/A

Considerations

•

You can transfer an outside call to a busy extension using Camp-on. See “Camping a Call Onto a

Busy Extension” on page 236.

Conference Calls

Description

Conference Calls allow you to add another party to an existing conversation. With the standard

system configuration, up to 4 parties can be included in a conference call at any one time. If the

optional Conference Card is installed, additional parties up to a total of 8 can participate in a

conference call.

Any combination of extensions and trunk lines can be in the conference as long as the original

extension is in the conference and the total number of parties does not exceed 8. Only one operation is

used to establish and add to a conference. You simply have to place the current call on hold, dial the

next party and press the

CONF

key. No different operation or access code is required to add

additional parties to the call.

When no optional conference card is installed, the system supports the following types of four-party

conference calls:

•

4 extensions

•

3 extensions and 1 trunk line

Action

Result

1. Lift the handset or press the

ON/OFF

key.

Intercom dial tone

2. Dial the extension number.

Busy tone

3. Enter the Camp-on (Call Waiting) code (default =

• Called party hears alert tone
• Calling party hears ringback tone

4. Remain on the line until the called party answers.

Action

Result

1. Replace the handset or press the

ON/OFF

key.

2. Lift the handset or press the

ON/OFF

key again to be con-

nected to the waiting call.

OR....

Press the

HOLD

key.

• Current call placed on hold
• Connected to waiting call

Summary of Contents for S-ics








































































































































































































































































































































Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands

Panasonic S-ics, Technical Manual

Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands