Panasonic S-ics Technical Manual Download

Page: 266 / 327

266

S-ICX (International) issued April 2002

S-ICX-64-700

Chapter 7. SLT Features

Section 700 - Operation

To cancel an Absence Message

Hardware Requirements

•

N/A

Related Programming

•

FF1 (System): Extension Class of Service Setting

•

FF3 (Extension): Extension Class of Service Assignment

•

FF8 (Maintenance): Absence Messages

Considerations

•

Calling parties without a display get a busy signal, rather than the Absence Message.

•

Regardless of setting an Absence Message on a DDI/DIL extension, DDI/DIL calls are routed

according to the trunk ringing setting.

•

An absence message may also be cancelled by dialling

7**

. This cancels Do-Not-Disturb (DND)

and Call Forwarding-All Calls as well.

Account Codes

Description

You can assign account codes to clients to facilitate billing and to track call dates and times, numbers

called, and outside line numbers used. This information is printed for each account on the Call

Logging record.

In addition verified account codes may be used to change the Toll Restriction Service (TRS) (Call

Barring) level to allow calls to numbers otherwise restricted.

Account codes may be either forced or unforced (voluntary) and either verified or unverified.

This feature works with Call Logging. Before making an outgoing call, a station user can silently

enter an accounting or client billing code. Then later, the Call Logging reports will show the Code

dialled for each call, and even sort the report by these Codes.

There are two different types of account codes: Non-Verified and Verified Account Codes. Prior to

Version 5.0, the maximum amount of account code numbers for both types could range from 1-10

digits. Beginning with Version 5.0, a second mode has been added that allows the user to set the

maximum amount of account code numbers from 1-4 digits. An account code error will occur when

more than the maximum number of digits are entered.

Action

Result

1. Lift the handset.

Intercom dial tone

2. Enter the Absence Message code (default =

729

3. Flash the hookswitch.

4. Replace the handset.

Summary of Contents for S-ics








































































































































































































































































































































Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands

Panasonic S-ics, Technical Manual

Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands