Panasonic S-ics Technical Manual Download

Page: 29 / 327

Section 700 - Operation

Chapter 3. System Features

S-ICX-64-700

S-ICX (International) issued April 2002

•

Caller ID data is usually sent between the first and the second rings of the incoming exchange

line call. The exchange line may be programmed to immediately ring at the station or wait until

after the Caller ID digits are received before ringing at the station. If the exchange line is

programmed to ring immediately, the Caller ID digits will not display until after they are

received and processed.

•

Caller ID numbers may be denied from being sent for some callers (private). Some long distance

carriers may not provide Caller ID data (out of area).

•

Caller ID only support the single format (number only). Multiple format (number and name) is

not supported.

•

Prior to Version 4.5, Caller ID supported only the number format. Version 4.5 and higher

supports selection of the number or name.

•

In Version 4.5, Caller ID displays the highest ringing priority call (call queued to ring at the

target extension immediately after the present call terminates).

Caller ID Alpha Tagging

Description

If the received Caller ID phone number matches any number in the System Speed Dials (SSD)

(SSD000-SSD199), then the associated SSD name can be displayed as the Caller ID information

instead of the Caller ID phone number. Alternatively, the Direct Dial Inward (DDI) name may be

displayed instead.
In Version 4.5 and higher, Caller ID information will be shown on the second line of the LCD display

when an incoming call rings a display phone with a conversation already in progress. Second

incoming calls include extension Camp-on, extension Call Wait, queued DIL, both Appearance and

non-Appearance calls (Exchange Line, MCO, virtual or DN, recall, BLF).

Hardware Requirements

•

ISDN (PRI = VB-44540UK, BRI = VB-44530UK)

•

ISDN (STBRI = VB-44531UK)

Considerations

•

The system may be set to display Caller ID in one of two priorities as follows:

Priority Choice 1

• CID name (future feature)
• Alpha tagging if matched
• DDI name

Priority Choice 2

• DDI name
• CID name (future feature)
• Alpha tagging if matched

•

Currently Caller ID only supports the single format (number only). Multiple format (number and

name) is not currently available but is planned as a future feature.

•

Caller ID Call Logging only shows the CID number.

Summary of Contents for S-ics








































































































































































































































































































































Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands

Panasonic S-ics, Technical Manual

Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands