Panasonic S-ics Technical Manual Download

Page: 62 / 327

S-ICX (International) issued April 2002

S-ICX-64-700

Chapter 3. System Features

Section 700 - Operation

Station Message Detail Recording (Call Logging)

Description

Station Message Detail Recording (SMDR) provides detailed call records of outgoing calls. This

record is printed on a serial printer connected to the RS-232C port. SMDR records can be output to a

printer or an external call accounting system.

Various types of information are reported on the SMDR record and each type of information occupies

a set position in the SMDR format. Three SMDR formats are available (See Figure 1 on page 63.)

One type of information is the “condition code” which occupies the first position in the output format.

This code specifies what type of call was made or received (e.g., DISA Incoming call [S] or Closed

Numbering call [W]). However, condition codes are prioritized, and the type of call determines what

code is displayed.

The following tables shows the priority of condition codes for outgoing calls and incoming calls.

Table 8.

Priority of outgoing call condition codes

For example, an outgoing call is an LRS Outgoing call (

) but it is also a transferred call. The Call

Logging data condition code will be

to indicate that the call was an Outgoing Transfer. (A

transferred call’s condition code takes precedence over the type of call - LRS Outgoing call [

].)

Table 9.

Priority of incoming call condition codes

For example, an incoming call is a DDI Incoming call (

), but it is also a transferred call. The Call

Logging data condition code will be

to indicate that the call was an Incoming Transfer call. (A

transferred call’s condition code takes precedence over the type of call - DDI Incoming call [

].)

Priority

Condition

Code

Description

Highest

T = Outgoing Transfer Call

H = Outgoing Hold Call

2nd

F = Call Forward Outside Call

3rd

W = Closed Numbering

Note:

In the case of an MCO outgoing call seizing the

private line, the condition code

is displayed.

4th

L = LCR Outgoing Call

Lowest

O = Outgoing Call

Priority

Condition

Code

Description

Highest

h = Incoming Hold

t = Incoming Transfer

2nd

, or

D = DDI Incoming Call

N = Network Incoming Call

S = DISA Incoming Call

Lowest

I = Incoming Call

A = Abandoned Call

Summary of Contents for S-ics








































































































































































































































































































































Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands

Panasonic S-ics, Technical Manual

Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands