Panasonic S-ics Technical Manual Download

Page: 69 / 327

Section 700 - Operation

Chapter 3. System Features

S-ICX-64-700

S-ICX (International) issued April 2002

DIL Delayed Incoming Ring Enhancement

Version 4.5 and higher

Prior to Version 4.5, a DIL call that was not answered by the Immediate Ringing extension was

simultaneously passed to all other extensions in the MCO if Delayed Ringing was set. Beginning with

Version 4.5, an incoming DIL call that is not answered can be passed to a single Delayed Ring

destination or to all extensions with an MCO key that includes the incoming exchange line. If the

Delayed Ringing extension is not answered, the call is forwarded the extension’s preprogrammed

location (e.g., Voice Mail, Call Forwarding, etc.) For example:

Note:

The program settings in the previous figure can also be used for the following Delayed

Ringing extension destinations:

- Speed Dial
- Hunt Group Number
- Attendant Group Number
- ERA Number

Hardware Requirements

•

N/A

Considerations

•

N/A

Multiple Ringing

Description

Multiple Ringing allows Exchange Line calls into the System to be directed to ring multiple

extensions in the System. This can be very useful when anyone in a group may answer a call. This can

also be very useful at night when only a selected number of people are available to handle calls.

DIL Immediate

(DIL Destination = 300)

DIL Delayed

(DIL Delayed Destination = 301)

Both Versions

Version 1.0

Version 4.5

FF2-0-BSSC-031 (DIL Dest. = 300)
1. Call rings on Ext. 300 only

FF2-0-BSSC-0441 (DIL Dest. = 300)
1. Call rings on Ext. 300
2. Call rolls over to Ext. 301, 302 and
303 simultaneously because they have
an MCO key that includes the
exchange line.

FF2-0-BSSC-041 (DIL Dest. = 300)
1. Call rings on Ext. 300
2. System can be programmed to ring
Ext. 301 only, or to ring all three
extensions.

Summary of Contents for S-ics








































































































































































































































































































































Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands

Panasonic S-ics, Technical Manual

Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands