13.2. Service Mode Table 1
The service modes can be activated by pressing various button combination on the player and remote control unit.
Player buttons
Remote control unit buttons
Application
Note
STOP
0
Error code display
(Refer to the item, “13.3.
DVD Self Diagnostic
Function-Error Code ”).
5
Tilt adjustment
Refer to the item “16.4.
Optical adjustment”).
6
Area number and broadcasting system check
7
Built-in program version check
DISPLAY
DVD laser drive current check
Refer to the item “13.1.
Optical Pickup
Breakdown Diagnosis ”.
3
CD laser drive current check
PAUSE
Writing of laser drive current value after replacement of optical
pickup (Do use this function only when optical pickup is
replaced.)
Initialization of the player (factory setting is restored.)
Used after replacement of micro-computer and its peripherals
and printed circuit board.
13.3. DVD Self Diagnostic Function-Error Code
Error Code
Error Content
Additional error explanation
U, H error
U11
Focus error
H01
Tray loading error
H02
Spindle servo error
(Spindle servo, DSC (IC8251) SP motor, CLV servo error)
H03
Traverse servo error
(Traverse motor, IC8251)
H04
Tracking servo error
H05
Seek error
H06
Power error
Cannot switch off the power because of the panel and system computer communication error
H07
Spindle motor drive error
Spindle motor
DSC related
F500
DSC error
DSC (IC8251) stops in the occurrence of servo error (startup, focus error, etc.)
F501
DSC not Ready error
DSC-system computer communication error (Communication failure caused by idling of DSC)
F502
DSC Time out error
Similar as F500
F503
DSC communication Failure
Communication error (result error occurred although communication command was sent)
F504
Error adjusting DSC data slice offset
F505
DSC Attention error
Similar as F500
F506
Invalid media
Disc is flipped over, TOC unreadable, incompatible disc media
ODC related
F600
Access
failure
to
management
information caused by demodulation
error
Operation stopped because navigation data is not accessible caused by the demodulation
defect
F601
Indeterminate sector ID requested
Operation stopped caused by the request to access abnormal ID data
F602
Access failure to LEAD-IN caused by
demodulation error
LEAD IN data unreadable
F603
Access failure to KEYDET caused by
demodulation error
Access failure to CSS data of disc
F610
ODC abnormality
No permission for command execution
F611
6626 QCODE don’t read Error
Access failure to seek address in CD series
F612
No CRC OK for a specific time
Access failure to ID data in DVD series
F620
Laser safeguard: high temperature
condition
F621
Laser
safeguard:
circuit
failure
condition
F630
No reply to KEY DET enquiry
(for internal use only)
F631
CPPM KEY DET is not available till
the FILE terminal
(CPPM file system is unreadable caused by scratches)
F632
CPPM KEY DET is not available
Been revoked or falsified
Disc code
F103
Illegal highlight Position
Big possibility of disc specification violation during highlight display
HIC Error
F4FF
Force initialize failure (time out)
Micro computer error
F700
MBX overflow
When replying message to disc manager
F701
Message command does not end
Next message is sent before replying to disc manager
F702
Message command changes
Message is changed before it is sent as a reply to disc manager
F880
Task number is not appropriate
Message coming from a non-existing task
30
SA-HT930P / SA-HT930PC / SA-HT930PX
Summary of Contents for SA-HT930P
