Item
Operational Condition
and Key Function
Details
Display
TO Exit Mode
Spindle use time
While
the
player
is
stopped and no disc is
inserted, press and hold
down the
button
on the player and the
button
on
the
remote controller unit.
Spindle motor usage time
T2_00000
The four-digit number is shown by
the ten hours in the decimal digit.
The number after 00000 is 99999.
Automatically exits
the mode after five
seconds.
Reset
spindle
use
time
While the usage time 2 is
displayed,
press
and
hold
down
the
button on the player and
the
button on the
remote controller unit.
Usage time 2 reset
Spindle motor usage time
T2_ _0000
Automatically exits
the mode after five
seconds.
User reset
While
the
player
is
stopped and no disc is
inserted, press “STOP” &
“ENTER”
on
remote
control.
Reset the unit.
“DVD RESET”
Automatically exits
the mode after five
seconds.
Communication error
display
While
the
player
is
stopped and no disc is
inserted, press and hold
down the
button
on the player and the
MENU
button
on
the
remote controller unit.
Press
“Dimmer/FL
Display” button for next
page
Displays frequency of communication
errors between system computer firm
IC and mechanical computer IC during
DVD module.
ECC_ _ _ 00
Press the STOP or
Open button on the
player.
14.7. CR16 Mechanism Ageing Mode
To perform the ageing mode:
1. Enter into Test mode.
2. Press [3] button on remote control. It enters into ageing mode. (see below for ageing process)
Ageing process:
1. Tray 1 open.
2. It waits for one second (Note: Do not put any disc into the tray.
3. Tray close.
4. TOC READ (Reading incomplete)
5. Tray 2 open & repeat step 1 to step 4. (Process repeat until Tray 5)
6. Tray check.
7. Whole process complete (Counter on FL increase by 1)
Note: To exit ageing mode, press [POWER] button. The unit will power down. Do not unplug the power cord until FL display shows
“GOODBYE”. This is to avoid tray jam problem.
14.8. Operation Lock Function
14.8.1. Setting
•
•
•
•
Operation Lock Function
1. With the DVD/CD/
and POWER ON, and then press the [POWER] KEY on the remote control for 3 seconds to enter
Lock mode B.
[_LOCKED_] will be displayed for 3 seconds, and the current disc will begin playing.
2. Lock mode B primarily controls the selector and disc operations, and disenables for the following keys.
Note:
OPEN/CLOSE
button are invalid and the player displays “_LOCKED_” while the lock function mode is entered.
•
•
•
•
Prohibiting operation of selector and disk
1. Select the DVD/CD/
function.
2. Press and hold down the DVD/CD/
button on the player and the power button on the remote controller unit for at least
three seconds. (The message, “_LOCKED_” appears when the function is activated.)
22
Summary of Contents for SA-TM900DVD
