14
RQT6361
Change this setting to listen to software recorded with Dolby Digital
at low volume (such as late at night) and maintain audio clarity. It
reduces the peak level in loud scenes without affecting the sound
field.
OFF: The software is played with the original dynamic range
(factory setting).
STANDARD: The level recommended by the producer of the
software for household viewing.
MAX: The maximum allowable compression (recommended for
night viewing).
1
1
Press [
] at the same time to enter
the setting mode.
2
2
Press [
] to select “DR-COMP”.
3
3
Turn [
] to select “OFF”, “STANDARD” or
“MAX”.
4
4
Press [
] at the same time to exit
the setting mode.
SFC MODE
w
q
INPUT SELECTOR
SFC MODE
w
q
SFC MODE
w
q
The factory setting is OFF (normal brightness).
1
1
Press [
] at the same time to enter
the setting mode.
2
2
Press [
] to select “DIMMER”.
3
3
Turn [
] to select “OFF” or “ON”.
4
4
Press [
] at the same time to exit
the setting mode.
SFC MODE
w
q
INPUT SELECTOR
SFC MODE
w
q
SFC MODE
w
q
Preset the stations one at a time.
1
1
Tune to the station.
2
2
Press [
].
3
3
Press [
] to select a channel.
4
4
Press [
].
MEMORY
TUNING
2
1
MEMORY
1
1
Press [
] to select “FM”.
2
2
Press [
] to tune to “FM 87.9 MHz”.
3
3
Press and hold [
].
The FM stations the unit can receive are preset in channels 1 to 30.
4
4
Press [
] to select “AM”.
5
5
Press [
] to tune to “AM 530 kHz”.
6
6
Press and hold [
].
The AM stations the unit can receive are preset in channels 21 to 30.
(FM stations are replaced if any were preset in these channels.)
During automatic presetting, the memory indicator (
˜
) flashes and
the frequency scrolls. The memory indicator and channel numbers
are displayed for a second when a station is preset.
The last station to be preset is displayed when presetting finishes.
MEMORY
TUNING
2
1
- BAND
– FM MODE
MEMORY
TUNING
2
1
- BAND
– FM MODE
1
1
Press [
].
The channel number flashes for about 5 seconds.
2
2
Press [
].
Hold down the buttons to change channels faster.
For your reference
Even if the power supply cord is disconnected from the household
AC outlet, the stations remain in memory for approximately one
month.
Improving reception
¡
DSP DEFEAT
Press and hold [
] until “DEFEAT” appears.
Press and hold [
] again to turn the DSP on.
While the DSP is defeated, you cannot:
– Select DSP sound modes,
– Adjust the tone,
– Output a test signal,
– Adjust individual speaker output, or
– Use digital input.
¡
For your reference
DVD players can interfere with radio reception. Turn the DVD
player off or move it further away from the antennas if this occurs.
Note
DSP
SOUND MODE
DSP
SOUND MODE
TUNING
2
1
PRESET
Presetting
Other settings
DR COMP –
Dynamic range compression
DIMMER –
Dim the unit’s display for better viewing in a
darkened room
Automatic presetting
Manual presetting
Selecting channels
POWER
SPEAKERS
SFC MODE
DOWN
UP
VOLUME
INPUT SELECTOR
DVD 6CH INPUT
SUBWOOFER
TAPE MONITOR
BASS/TREBLE
3
4
BALANCE
L
R
DIGITAL INPUT
PHONES
- HELP
– RESET
- BAND
– FM MODE MEMORY
TUNING
PRESET
DSP
SOUND MODE
DOLBY
PRO LOGIC
2
8
2
w
q
1
DSP
SOUND MODE
TUNING
MEMORY
PRESET
2
1
- BAND
– FM MODE
POWER
SPEAKERS
SFC MODE
DOWN
UP
VOLUME
INPUT SELECTOR
DVD 6CH INPUT
SUBWOOFER
TAPE MONITOR
BASS/TREBLE
3
4
BALANCE
L
R
DIGITAL INPUT
PHONES
- HELP
– RESET
- BAND
– FM MODE MEMORY
TUNING
PRESET
DSP
SOUND MODE
DOLBY
PRO LOGIC
2
8
2
w
q
1
INPUT SELECTOR
SFC MODE
w
q
