24
RQT6945
Radio operations
The radio
AV SYSTEM
SLEEP
FL DISPLAY
DIMMER
PLAY MODE
MIX 2CH
REPEAT
CANCEL
SKIP
CH
TOP MENU
DISPLAY
VOLUME
MUTING
PL
C.FOCUS
SFC
SUBWOOFER
LEVEL
FM MODE
SETUP
ZOOM
GROUP
AUDIO
RETURN
TV VOL
TV VOL
DIRECT
NAVIGATOR
PLAY LIST
MENU
SLOW/SEARCH
1
2
3
4
5
6
7
8
0
9
TUNER/BAND DVD/CD
TV
VCR/AUX
ENTER
CH SELECT
TEST
TV/VIDEO
POSITION
MEMORY
S.SRND
C.S.M
10/ ENTER
>
=
TUNER/BAND
ENTER
FM MODE
SKIP
u
i
2
CH
1
SLOW/SEARCH
t
y
Numbered
buttons
VOLUME
– +
Manual tuning
1
Press [TUNER/BAND] to select “FM”
or “AM”.
2
Press [
t
] or [
y
] to select the
frequency of the required station.
TUNED: Displayed when a radio station
is tuned.
ST: Displayed when a stereo FM
broadcast is being received.
Press and hold [
t
] or [
y
] until the frequency starts
scrolling to start automatic tuning. Tuning stops when a
station is found.
3
Adjust the volume.
■
If noise is excessive in FM
Press [FM MODE] to display “MONO”.
Press [FM MODE] again to cancel the mode.
The mode is also canceled when you changed the frequency.
■
FM frequency step
The step is factory-set to 0.2 MHz, but you can change it to receive
broadcasts allocated 0.1-MHz steps.
1 Press [TUNER/BAND] to select “FM”.
2 Press and hold [TUNER/BAND].
After a few seconds the display changes to show the current
minimum frequency. Continue to hold the button down. The
minimum frequency changes and the step is changed.
To return to the original step, repeat the above steps.
Any FM frequencies preset in channels will be changed by this
procedure. Preset them again.
■
When you receive poor AM radio reception
Turn off the television if it is too close to the unit.
Note
TUNED
ST
MONO
Preset tuning
Preset channels to make selection simple.
Up to 15 stations can each be set in the FM and AM bands.
Automatic presetting
1
Tune to “FM 87.9 MHz” or
“FM 87.5 MHz” (
\
\
left).
2
Press and hold [ENTER].
Release the button when “FM AUTO” is displayed.
The tuner presets all the stations it can receive into the
channels in ascending order.
“SET OK” is displayed when the stations are set. The last
station to be set is then played.
3
Tune to “AM 520 kHz”.
4
Press and hold [ENTER].
■
“ERROR” is displayed
Presetting was unsuccessful. Preset manually.
Manual presetting
1
Tune to the station (
\
\
left).
2
Press [ENTER].
3
While “PGM” is flashing
Press the numbered buttons to select
a channel.
Alternatively, press [
u
,
2
CH] or [
i
, CH
1
] then press
[ENTER].
The station occupying a channel is erased if another station is
preset in that channel.
PGM
CH 1
Selecting channels
1
Press [TUNER/BAND] to select “FM”
or “AM”.
2
Press the numbered buttons or
[
u
,
2
CH] or [
i
, CH
1
] to select
the channel.
To select a 2-digit number
Example: To select channel 12, press [>
=10]
\
[1]
\
[2].
PGM
CH 2
