T
Q
BJ09
96
20
“Linking”
• This system is trying to connect to the last connected
Bluetooth
®
device when “BLUETOOTH” is selected.
• This system is communicating with the wireless router
to complete the network settings.
Depending on the wireless router this process may
take a few minutes. Try moving this system closer to
the wireless router.
“Network Initializing”
“Setup in Progress, Try Again”
• The system is carrying out an internal process.
– Wait for approximately 3 minutes.
– Do not disconnect the AC power supply cord. Doing so
may cause malfunction.
“No Connect”
• This system cannot connect to the network.
Check the network connection. (
6)
“No Device”
• The iPhone/iPad/iPod or USB device is not connected.
Examine the connection.
• The battery of the iPhone/iPad/iPod is depleted.
Charge the iPhone/iPad/iPod and turn it on before
connecting.
“No Disc”
• You have not put in a disc or put in a disc that the
system cannot play.
“No Play”
• Examine the content. You can only play supported
format. (
21)
• The files in the USB device can be corrupted. Format
the USB device and try again.
• The unit may have a problem. Turn the unit off and
then on again.
“No Preset”
• The selected preset channel has not been preset.
Preset some channels. (
10)
“Device No Response”
“Hub Not Supported”
“Not Supported”
• You have connected an iPhone/iPad/iPod that cannot
be played.
• If the iPhone/iPad/iPod is compatible, turn it on and
connect it correctly.
• You have connected an unsupported USB device.
“PC Unlocked”
• “PC” is selected, but a PC is not connected.
“PGM Full”
• The number of programed tracks is more than 24.
“Playerror”
• You played an unsupported file. The system will skip
that track and play the next one.
“Please Wait”
• When audio switching needs longer time (e.g., when
start/stop re-streaming or group and ungroup with
other speakers).
“Reading”
• The unit is checking the CD information. After this
display has disappeared, start operating.
• When starting playback of DSD files, it may take time
to read the file. Wait until reading completes.
“Remote
” (“
” stands for a number.)
• The remote control and this unit are using different
codes. Change the code on the remote control.
– When “Remote 1” is displayed, press and hold [OK] and
[1] for at least 4 seconds.
– When “Remote 2” is displayed, press and hold [OK] and
[2] for at least 4 seconds.
“USB Over Current Error”
• The iPhone/iPad/iPod or USB device is drawing too
much power. Remove the iPhone/iPad/iPod or USB
device. Switch the system off and on again.
“VBR”
• The system cannot show the remaining play time for
variable bit rate (VBR) tracks.
“WAC Mode”
• “Method 1” of network setting method is available.
(
6)
• To exit “WAC Mode”, press [
∫
].
“Wait”
• This is displayed, for example, when this unit is turning
off.
• This is flashing when the system is trying to enter a
network setting mode.
“
” blinks
• This may occur when, for instance, the network
connection is interrupted.
Reset the memory when the following situations occur:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.
1
Disconnect the AC power supply cord.
Wait 30 seconds before you continue with step 2.
2
While you press and hold [
Í
/I] on the main unit,
connect the AC power supply cord again.
Keep holding down [
Í
/I] until “------------” appears on
the display.
3
Release [
Í
/I].
The settings are returned to the factory defaults.
It is necessary to set the memory items again.
• To reset the network settings, perform the operation for
network reset. (
17)
When other Panasonic equipment responds to the
remote control of this system, change the remote control
code for this system.
To set the code to “Remote 2”
1
Press [SELECTOR, -NET PRESET] on the main
unit to select “CD”.
2
Press and hold [
∫
] on the main unit and [2] on
the remote control until “Remote 2” is shown.
3
Press and hold [OK] and [2] for a minimum of
4 seconds.
• The factory default is “Remote 1”.
• To change the mode back to “Remote 1”, repeat the
steps above but replace the button pressed on the
remote control from [2] to [1].
Memory reset (initialization)
Remote control code
SC-PMX150_PC-TQBJ0996_eng.book 20 ページ ２０１７年２月２７日 月曜日 午後５時２５分
