4
Chapter 4 Adjustments and settings for recording
45
#
< VF MARKER >
MKR:A
TABLE :A
CENTER MARK :1
SAFETY ZONE :2
SAFETY AREA :90%
FRAME SIG :4:3
FRAME MARK :OFF
FLAME LVL :15
#
< CAMERA ID >
ID1 : ABCDEFGHIJ
ID2 : ABCDEFGHIJ
ID3 : ABCDEFGHIJ
4-7-6 Setting the camera ID
The camera ID is set on the CAMERA ID screen.
Up to ten alphanumerics, symbols and spaces can be used.
<Note>
The camera ID is not displayed while the setting menu is
displayed even if color bar signals are output.
4-7-5 Setting the marker displays
ON, OFF or the display type can be selected for the displays
of the center marker, safety zone markers, safety zone area
and frame marker. To make the selection, perform menu
operations to open the <VF MARKER> screen from the VF
page and select the display mode for each item.
For details on operation, refer to “4-6-2 Basic menu
operations.”
1
Perform a menu operation to open the <CAMERA ID>
screen from the OPERATION page.
2
Turn the JOG dial button to move the arrow (cursor) to
the “ID 1: to 3:” item.
±
±
:
Message is to be
displayed.
a
a
:
Message is not to
be displayed.
Setting change/adjustment result messages and display modes
Situation in which message is displayed
Message
Display mode
setting
1
2
3
a
a
a
a
±
±
When the filter selection has been changed
FILTER: n (n=1, 2, 3, 4)
a
a
a
a
±
±
When the gain setting has been changed
GAIN: n dB
(n= –3, 0, 3, 6, 9, 12, 15, 18, 21, 24, 27, 30)
a
a
a
a
±
±
When the WHITE BAL switch setting has been changed WHITE: n (n=ACH, BCH, PRESET)
a
a
±
±
±
±
When the OUTPUT/AUTO KNEE switch has been set
to AUTO KNEE or OFF
AUTO KNEE: ON (or OFF)
a
a
±
±
±
±
When the shutter speed/mode setting has been changed
SS: 1/60 (or 1/120, 1/250, 1/500, 1/1000, 1/2000, S.SCAN)
a
a
±
±
±
±
When the white balance (AWB) has been adjusted
Example) AWB A OK 3.2K
a
a
±
±
±
±
When the black balance (ABB) has been adjusted
Example) ABB OK
a
a
a
a
±
±
When the extender has been selected
Example) EXTENDER ON
a
a
±
±
±
±
When a user button has been selected
Example) UM: S.GAIN 30 dB
a
a
a
a
±
±
When a marker select button has been selected
Example) MKR: A
a
a
±
±
±
±
When in iris overwrite status
Example) ++ F 5.6
4-7-4 Display modes and setting
changes/adjustment result messages
By setting the display mode item, it is possible to select
various display methods for the changes made in the settings
and for the messages advising the user of the adjustment
results: for instance, the items displayed can be limited to a
select number or not displayed at all. To select the display
mode, perform menu operations to open the <VF DISPLAY>
screen from the VF page and select the setting for the DISP
MODE item.
For details on operation, refer to “4-6-2 Basic menu operations.”
<Note>
The MKR: A indication at the upper right of the screen shows
the display status. To check the settings for TABLE B, press
the MARKER SELECT so that MKR:B is displayed.
#
< VF DISPLAY >
DISP CONDITION :NORMAL
DISP MODE :3
VF OUT :Y
VF DTL :3
ZEBRA1 DETECT :070%
ZEBRA2 DETECT :085%
ZEBRA2 :SPOT
LOW LIGHT LVL :35%
ECU MENU DISP. :OFF
50M INDICATOR :OFF
MARKER/CHAR LVL :50%
SDC905
