64
© Panasonic Industrial Devices SUNX Co., Ltd. 2012 MJEC-SF4B01V2 No.0027-44V
English
!
!##!+& "& !+
Type
10mm pitch type
20mm pitch type
40mm pitch type
Model No.
SF4B-F
-01<V2>
SF4B-H
-01<V2>
SF4B-A
-01<V2>
Detecting capability
(Min. sensing object)
ø14mm opaque object
ø25mm opaque object
ø45mm opaque object
E f f e c t i v e a p e r t u r e
angle (EAA)
±2.5 degree or less
[for sensing range exceeding 3m(Required by IEC 61496-2, ANSI/UL 61496-2)]
Supply voltage
24V DC ±10% Ripple P-P 10% or less
Control output
(OSSD 1 / 2)
PNP open-collector transistor / NPN open-collector transistor (switching type)
<For PNP output>
Maximum source current: 200mA
Applied voltage: same as supply voltage
(between the control output and +V)
Residual voltage: 2.5V or less
(source current 200mA, when using 20m length cable)
Leakage current: 0.1mA or less
(power supply OFF condition)
Maximum load capacity: 0.22μF
(No load to maximum output current)
{j |"+
<For NPN output>
Maximum sink current: 200mA
Applied voltage: same as supply voltage
(between the control output and 0V)
Residual voltage: 2.5V or less
(sink current 200mA, when using 20m length cable)
Leakage current: 0.1mA or less
(power supply OFF condition)
Maximum load capacity: 0.22μF
(No load to maximum output current)
{j |"+
Operation mode
(Output operation)
ON when all beams are received, OFF when one or more beams are interrupted (Note 1)
(OFF when fault occurs in the sensor or the synchronization signal error, too)
Protection circuit
(Short-circuit protection)
Incorporated
Response time
(In normal operation)
ON response: 14ms or less, OFF response: 80 to 90ms
Auxiliary output
(Non-safety output)
PNP open-collector transistor / NPN open-collector transistor (switching type)
<For PNP output>
Maximum source current: 100mA
Applied voltage: same as supply voltage
(between the auxiliary output and +V)
Residual voltage: 2.5V or less
(source current 100mA, when using 20m length cable)
<For NPN output>
Maximum sink current: 100mA
Applied voltage: same as supply voltage
(between the auxiliary output and 0V)
Residual voltage: 2.5V or less
(sink current 100mA, when using 20m length cable)
Operation mode
(Output operation)
When OSSDs are ON: OFF, when OSSDs are OFF: ON
Protection circuit
(Short-circuit protection)
Incorporated
Protection
IP65, IP67 (IEC)
Degree of pollution
3
Ambient temperature
-10 to +55°C (No dew condensation or icing allowed), Storage: -25 to +70°C
Ambient humidity
30 to 85% RH, Storage: 30 to 95% RH
Ambient illuminance
Incandescent lamp: 3,500$x or less at the light-receiving surface
Operating altitude
2,000m or less
Voltage withstandability
1,000V AC for one min. (between all supply terminals connected together and enclosure)
Insulation resistance
&'*+]{''@Q<]j
(between all supply terminals connected together and enclosure)
Vibration resistance
10 to 55Hz frequency, 0.75mm amplitude in X, Y and Z directions for two hours each
Shock resistance
300m/s
2
acceleration (approx. 30G) in X, Y and Z directions for three times each
Cable extension
Extension up to total 50m is possible for both emitter and receiver connecting cable
(optional) (Note 2)
Notes: 1) The beam channel is not turned OFF during muting even if it is blocked.
2) The cable can be extended within 30m (for emitter / receiver) when two devices are connected in
series connection, within 20m when three devices are connected in series connection. Furthermore,
when the muting lamp is used, the cable can be extended within 40m (for emitter / receiver).
