Panasonic Super Dynamic III WV-CW964, Operating Instructions Manual

4. Input an area title. 

The text input procedure is the same as that for
camera ID input. 
See steps 3 through 5 under “Camera ID Settings”
on page 22 for information about inputting the text
for the area title and specifying its position on the
display. 

5. Repeat steps 1 through 4 for the other area

numbers, if you want. 

(13) Tilt Angle Setting (TILT ANGLE) 

Selecting 5° for the TILT ANGLE setting allows tilting
past horizontal, in the range of -5° to 185°. 

1. Move  the cursor to TILT ANGLE, and then tilt the

joystick left or right to toggle the setting between 0°
and 5°. 

Notes:

• Zooming to WIDE while 5° is selected for the

TILT angle setting will cause the upper half of
the picture to become hidden.

• With certain subjects, AGC (gain control) can

cause the image to become white.  

(14) Cleaning Settings (CLEANING) 

This camera uses a "slip ring" for transmission of
electrical power and signals. A dirty slip ring can cause
deterioration of picture quality and generation of noise. 
The cleaning function performs cleaning approximately
once a week to keep the slip ring clean. 

1. Move the cursor to CLEANING, and then tilt the

joystick left or right to toggle it on and off. 
The text CLEANING appears in the center of the
screen while the cleaning process is being
performed. 

Note:

Select OFF for CLEANING when the system

controller uploads or downloads the preset data.
This protects against the download or upload failure
due to start up of the cleaning process. 

6. Use the joystick to select an area title display

position, and then press the MON (ESC) button. 
This registers the area title display position and
returns to the area title (NESW) setting menu. 

Note:

The area title is always displayed under the

camera ID. If you specify different display position
settings for the camera ID and the area title ID, the
area title ID display position setting is used for both. 

(2) When ON (USER) is selected 
After selecting ON (USER), you can use the area title
(USER) setting menu to configure detailed settings.
You can use the following procedure to configure
direction settings, and to input text associated with a
particular direction indicator. 

1. Move the cursor to 1, and then press the CAM

(SET) button. 
This will display the position setting menu. An asterisk
(*) to the right of an area title number indicates that it
already has an area title assigned to it.
If the there is already text associated with the
direction you selected, it will appear under the
cross mark (+). If there is no text associated with
the direction, only the cross mark (+) will be
displayed. 

2. Adjust the camera orientation (pan and tilt), zoom,

and focus. 
Perform steps 1 through 4 under “(1) When ON
(NESW) is selected” on page 37. 

3. Move the joystick to the right to align the cursor with

the title display, and press the CAM (SET) button. 
This will display the area title setting menu. 
In the example screen shown in step 1, NORTH 

O

is the title name of area title number 1. 

-38-

FLOOR 1
N

   **AREA TITLE(USER)**
       NORTH
 2
 3     
 4     
 5     
 6     
 7
 8     

 RET TOP RESET

1*

     AREA TITLE 1
      123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,'":;&#!?=
     +-*/%$

    SPACE     
    ---- POSI RET RESET

    ................
    

 0

→

PUSH SET

  **DIRECTION(USER) 1**
PAN/TILT
ZOOM/FOCUS

            +
          NORTH

 RET TOP DEL

→

PUSH SET

FLOOR 1
NORTH

 WV-CW964  05.10.18  11:09 AM  ページ38