154
4
4
.
.
7
7
.
.
7
7
.
.
E
E
g
g
r
r
e
e
s
s
s
s
R
R
a
a
t
t
e
e
L
L
i
i
m
m
i
i
t
t
i
i
n
n
g
g
C
C
o
o
n
n
f
f
i
i
g
g
u
u
r
r
a
a
t
t
i
i
o
o
n
n
M
M
e
e
n
n
u
u
On the Quality of Service Configuration Menu, pressing "C" opens the Egress
Rate Limiting Configuration Menu, as shown in Fig. 4-7-41. On this screen,
you can set bandwidth control.
Fig. 4-7-41 Egress Rate Limiting Configuration
Screen Description
Port
Displays the port number.
Bandwidth
Displays the bandwidth. A default for ports 1 to 12 is 100, and a
default for ports 13 and 14 is 1000. The unit is ‘Mbps’.
Status:
Enables/disables egress rate limiting configuration.
Enabled
Egress rate limiting is enabled.
Disabled
Egress rate limiting is disabled.
Available commands are listed below.
N Display the next page.
Press "N" to change the display to the next page.
P Display the previous page.
Press "P" to change the display to the previous page.
B Set a bandwidth.
Press "B" to change the command prompt to "Enter port number e.g.: 1, 3,
5-12>." Enter a port number to designate. Then, the command prompt changes
to "Enter bandwidth>." For ports 1 to 12, enter bandwidth from 1 to 100. For
ports 13 and 14, enter from 1 to 1000.
S Set the egress rate limit status.
PN23129K/PN23129A Local Management System
Quality of Service Configuration -> Egress Rate Limiting Configuration Menu
Port Bandwidth Status
---- ----------- --------
1 100 Disabled
2 100 Disabled
3 100 Disabled
4 100 Disabled
5 100 Disabled
6 100 Disabled
7 100 Disabled
8 100 Disabled
9 100 Disabled
10 100 Disabled
11 100 Disabled
12 100 Disabled
Note: Bandwidth - 1Mbps/unit
-------------------------------- <COMMAND> -----------------------------------
[N]ext Page Set [S]tatus
[P]revious Page [Q]uit to previous menu
Set [B]andwidth
Command>
Enter the character in square brackets to select option
Summary of Contents for Switch-M12PWR
