Panasonic T-Mobile KX-HDV130 Administrator'S Manual Download

Page: 200 / 332

Value Range

•

(Enable)

•

(Disable)

Default Value

PERIODIC_INFORM_INTERVAL

Value Format

INTEGER

Description

Specifies the interval length, in seconds, when the CPE must attempt
to connect with the ACS and call the Inform method.

Note

•

This setting is available only when
"

PERIODIC_INFORM_ENABLE

" is set to "

Value Range

30–2419200

Default Value

180

PERIODIC_INFORM_TIME

Value Format

STRING

Description

Specifies the time (UTC) to determine when the CPE will initiate the
periodic Inform method calls.

Note

•

Each Inform call must occur at this reference time plus or minus
an integer multiple of the "

PERIODIC_INFORM_INTERVAL

This "

PERIODIC_INFORM_TIME

" parameter is used only to set

the "phase" of the periodic Informs. The actual value can be
arbitrarily set far into the past or future.
For example, if "

PERIODIC_INFORM_INTERVAL

" is set to

86400 (one day) and if "

PERIODIC_INFORM_TIME

" is set to

midnight on a certain day, then periodic Informs will occur every
day at midnight, starting from the set date.

•

If the time is set to "unknown time", the start time depends on
the CPE’s settings. However, the
"

PERIODIC_INFORM_INTERVAL

" must still be adhered to.

If absolute time is not available to the CPE, its periodic Inform
behavior must be the same as if the
"

PERIODIC_INFORM_TIME

" parameter was set to the

"unknown time".

•

Time zones other than UTC are not supported.

Value Range

4–32 characters
date and time format

Default Value

0001-01-01T00:00:00Z

200

Administrator Guide

Document Version 2015-12

5.3.9 TR-069 Settings

Summary of Contents for T-Mobile KX-HDV130













































































































































































































































































































































Search results

Summary of Contents for T-Mobile KX-HDV130

Reviews:

Related manuals for T-Mobile KX-HDV130

Brands by name

Popular brands

Panasonic T-Mobile KX-HDV130, Administrator'S Manual

Search results

Summary of Contents for T-Mobile KX-HDV130

Reviews:

Related manuals for T-Mobile KX-HDV130

Brands by name

Popular brands