Panasonic T-Mobile KX-HDV130 Administrator'S Manual Download

Page: 326 / 332

Time

Problem

Cause/Solution

The time is not correct.

•

In the Web user interface, you can set NTP
synchronization and DST (Summer Time) control to adjust
the time automatically (

see

4.4.4 Time Adjust

Settings

•

If the time is still incorrect even after setting NTP
synchronization, check the firewall and port forwarding
settings on the router.

Error Codes

During operation, error messages might appear on the unit. The following table lists these messages and
possible causes and solutions.

Error code

Probable Cause

Solution

Error:001

LAN disconnection
detected

Check the LAN cables connections.

Error:002

Overlapping IP addresses

Check the IP addresses and re-set them.
For making settings using a unit, see 1.1.3 Basic Network
Setup.

Error:003

The REGISTER of the SIP
server has not been
registered.

Consult your network administrator or phone system
dealer.

Error Message

Probable Cause

Solution

Need Repair

Hardware failure

Consult your network administrator or phone system
dealer.

Checking the Status of the Unit

You can check the status of the unit by using Web user interface programming (

4.2.3 VoIP Status

) or by looking at system logs (

see

5.3.34 Logging Settings

) sent from the

unit.

To check the setting status in the Web user interface
1.

Click the

[Status]

tab, and then click

[Network Status]

to check the network settings.

Check the status displayed.

Click

[VoIP Status]

to check the VoIP settings.

Check the status displayed.

To check the setting status using the Unit
1.
2.

[ ]/[ ]: "

System Settings

326

Administrator Guide

Document Version 2015-12

8.1 Troubleshooting

Summary of Contents for T-Mobile KX-HDV130













































































































































































































































































































































Search results

Summary of Contents for T-Mobile KX-HDV130

Reviews:

Related manuals for T-Mobile KX-HDV130

Brands by name

Popular brands

Panasonic T-Mobile KX-HDV130, Administrator'S Manual

Search results

Summary of Contents for T-Mobile KX-HDV130

Reviews:

Related manuals for T-Mobile KX-HDV130

Brands by name

Popular brands